Maft pro running problems

cre · 09-28-2012, 06:31 AM

Quote:

Originally Posted by 1989toyotasupraandpickup

How exactly do you disable ptt and wot tracking.

http://www.fadingworld.com/CRE/Autom...nual%205.x.php

You didn't read it all. With WOT tracking min TPS sets the minimum the TPS signal must be at for WOT AFR tracking to be active. In this menu you want to set it higher than is realistic. Set it for 5v+. Alternatively you may set either min RPM or min Load higher than possible (ie: setting min RPM for 8000), OR you may set Gain to 0. It's a bit confusing that PT and WOT tracking are the opposite.... I really figured Bob would have done something about that by now.

Now, if you haven't made any significant changes to the car's fuel system you should be able to zero out the fuel maps and the car should fairly normally. Now is the time to adjust the trim and tip in/out (decay) settings. Then once it feels good, disconnect the O2 sensor and see what needs tweaked. Then plug the O2 sensor back in, setup the ETPS system and tune for upper-mid and WOT and let the ECU deal with the lower loads.

1989toyotasupraandpickup · 09-28-2012, 07:59 PM

Thank you cre for that link. it really helped me out and everyday i am learning something new about the system. im not perfect at it but at least im trying and i have people on here that will help me you in particular!!!!! Thank you so much and im sorry for all the questions you may think are dumb questions. I will tweak with the settings. still trying to learn about the vf signal and how to enable it on the maft pro and how to view it on the sensor screen. if you could give any advise that would be great. Thanks again cre!!!!!!

cre · 09-28-2012, 10:45 PM

I've never found Vf to be all that useful for tuning. It's a decent diagnostic aid but unless you're trying to maintain a stock tune it's not really helpful. Setting it up is easy enough, you wire the Vf pin to one of the MAFT Pro aux inputs, set the Aux In parapeter in the MAFT Pro's CFG Settings menu to 0 and then in the SensorMonitor you set one of the four monitors to Ax1 to see the readout (0v to 5v). You'll need to define the input in TunerPro if you want it to show up in TunerPro's logs.

1989toyotasupraandpickup · 10-01-2012, 08:08 PM

CRE. It will not let me load up the file for you. i was going to attach the log file but it says invalid. can i send the file to you?

cre · 10-01-2012, 10:58 PM

You should be able to attach it by either zipping it up in a zip archive or possibly by adding .txt or .zip to the file name after the real extension.

1989toyotasupraandpickup · 10-01-2012, 11:13 PM

ok i think i got it. take a look and make sure that i have the right files. they seem to work good. the log has 2 sessions. the first one is the driving no boost and the other is the one under boost. Thanks.

1989toyotasupraandpickup · 10-02-2012, 05:46 PM

Here is the bin file forgot to add that to the zip file i gave you. sorry

09-28-2012, 10:45 PM	#3
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	I've never found Vf to be all that useful for tuning. It's a decent diagnostic aid but unless you're trying to maintain a stock tune it's not really helpful. Setting it up is easy enough, you wire the Vf pin to one of the MAFT Pro aux inputs, set the Aux In parapeter in the MAFT Pro's CFG Settings menu to 0 and then in the SensorMonitor you set one of the four monitors to Ax1 to see the readout (0v to 5v). You'll need to define the input in TunerPro if you want it to show up in TunerPro's logs. __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

10-01-2012, 10:58 PM	#5
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	You should be able to attach it by either zipping it up in a zip archive or possibly by adding .txt or .zip to the file name after the real extension. __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MAFT Pro or something newer/better now	icey756	MKIII FAQ	10	11-06-2011 05:36 AM
MAFT questions?	turbonicsperformance	MKIII Supra	3	08-11-2011 07:22 AM
problems problems problems....	86SupraMan	MKIII Supra	5	02-04-2008 04:28 PM
Starting problems and accleration problems!	alekjame22	MKIII Supra	6	03-17-2007 11:19 PM
problems, problems, and problems	tone loc	MKIII Supra	6	09-06-2006 04:35 AM

09-28-2012, 07:59 PM	#2
1989toyotasupraandpickup Stock Join Date: Jun 2012 Location: ny Posts: 26	Thank you cre for that link. it really helped me out and everyday i am learning something new about the system. im not perfect at it but at least im trying and i have people on here that will help me you in particular!!!!! Thank you so much and im sorry for all the questions you may think are dumb questions. I will tweak with the settings. still trying to learn about the vf signal and how to enable it on the maft pro and how to view it on the sensor screen. if you could give any advise that would be great. Thanks again cre!!!!!!

10-01-2012, 08:08 PM	#4
1989toyotasupraandpickup Stock Join Date: Jun 2012 Location: ny Posts: 26	CRE. It will not let me load up the file for you. i was going to attach the log file but it says invalid. can i send the file to you?