Ma and Pa Kettle change their brakes!

Green7mgte · 01-13-2010, 11:21 PM

After everything is re assembled I go to bleed my brakes cause I removed my caliper. I think I might of ruined my master cylinder.
Brakes havent been bled in the 4 years I had the car in my possession. I assume its the Stock MC. When my peddle went down to the floor I probably blew a ring. I put about a bottle and 1/2 through the MC. I bled my brakes till I could clearly see clean fluid comming out and no longer had any air bubbles. I even bled the lines directly From the MC itself as a final test. Still when I start the car my peddle falls flat. Sure ill have pressure for the first pump or so but its steadily decreases till its loosy goosy! Im purchasing a MC tonight have it in tomorrow. but before I install it I would like to know if there is any other tests i can preform or any suggestions to eliminate air in line as a problem and pinpoint MC as culprit.
thanks

Found this for anyone having the same problems
http://www.toyota-supra.info/forums/...-wtffffff.html
this is the TSRM Removal
http://www.cygnusx1.net/Supra/Librar...aspx?S=BR&P=15
TSRM Parts
http://www.cygnusx1.net/Supra/Librar...spx?F=4702&P=1
And Don't forget to Bench Bleed your new MC
http://www.youtube.com/watch?v=oGVnS...eature=related
(for all you non readers, youtube.)

hope this helps people in the future

01-13-2010, 11:21 PM	#17
Green7mgte Supra Forum Moderator Join Date: Nov 2009 Location: Green-Ohio Posts: 1,297	Brake bleeding issue After everything is re assembled I go to bleed my brakes cause I removed my caliper. I think I might of ruined my master cylinder. Brakes havent been bled in the 4 years I had the car in my possession. I assume its the Stock MC. When my peddle went down to the floor I probably blew a ring. I put about a bottle and 1/2 through the MC. I bled my brakes till I could clearly see clean fluid comming out and no longer had any air bubbles. I even bled the lines directly From the MC itself as a final test. Still when I start the car my peddle falls flat. Sure ill have pressure for the first pump or so but its steadily decreases till its loosy goosy! Im purchasing a MC tonight have it in tomorrow. but before I install it I would like to know if there is any other tests i can preform or any suggestions to eliminate air in line as a problem and pinpoint MC as culprit. thanks Found this for anyone having the same problems http://www.toyota-supra.info/forums/...-wtffffff.html this is the TSRM Removal http://www.cygnusx1.net/Supra/Librar...aspx?S=BR&P=15 TSRM Parts http://www.cygnusx1.net/Supra/Librar...spx?F=4702&P=1 And Don't forget to Bench Bleed your new MC http://www.youtube.com/watch?v=oGVnS...eature=related (for all you non readers, youtube.) hope this helps people in the future __________________ 92 Ma71 7mGTE Auto. SafcII Supra FAQ Supra MKIII FAQ Classified Section guidelines : Last edited by Green7mgte; 01-14-2010 at 01:24 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Two Issues: Front Brakes and Sporadic Vibration	Chambers	MKIII Supra	0	11-03-2007 04:15 PM
Front Brakes	zuni	MKIII Supra	8	06-21-2007 05:09 PM
Brakes 5M Vs. 7MGTE	panda-supra	MKII Supra	3	03-22-2006 09:07 AM
Should I STILL change head gasket??	lifesnotfair	MKIII Supra	7	01-13-2006 01:08 AM
Brakes acting up	maksimus54	Non-Generation Specific Questions	4	07-06-2005 11:47 PM