nuts and bolts

87mk3moneypit · 09-20-2005, 02:04 PM

the engine is almost all the way back together. The head, turbo, flywheel are on. I don't have any of the bolts for the pressure plate, bellhousing, or any of the connecting brackets

rnoswal · 09-20-2005, 08:22 PM

Oh well then..................those bolts are easy to find on any other Toyota in the junkyard. The bolts that hold the pressure plate are all the same, 12 mm head, about 3/4 of an inch long. The brackect on the sides are the same as any other front engine rear drive Toyota. They are all 14 mm heads about an inch to an inch and a half long. The bell housings are also 14 mm heads but about 3 inches long. My Supra has the 14 mm head bolts while my 22R 4 cylinder used the 17 mm head sized bolts to hold the bell housing together, never had either one break, but just seemed odd.

The bolts holding the trans mount to the frame where just 12 mm heads on the supra and the ones to the trans had 14 mm heads. The nuts on the lower side if the engine mounts were 19 mm heads and the bolts that held the motor brackets to the block were all 14 mm heads 3/4 to 1 inch in length.

Hope that helps some,

Russ

87mk3moneypit · 09-21-2005, 01:42 AM

which is beter the chilton's or the Haynes

suprra_girl · 09-21-2005, 12:08 PM

neither LOL

this one is the best

www.supratsrm.com

09-21-2005, 12:08 PM	#4
suprra_girl 7M POWAH! ;) Join Date: Jun 2004 Location: New Zealand Posts: 2,312	neither LOL this one is the best www.supratsrm.com __________________ Please use the forum to ask your questions as they will get replied to much faster than pming me Pics of my build. "Good girls are just bad girls that don't get caught" Do a diagnostic first!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
engine removal	mizuboi	MKIII Supra	11	06-10-2011 06:25 AM
Blown Head Gasket repair w/pics	IHateHacks	MKIII FAQ	226	02-21-2011 05:32 AM
Head Bolt Retorquing	Benesesso	MKIII Supra	8	11-07-2006 03:49 PM
Timing Belt Change, Do It at Home	mrnickleye	Supra FAQ	2	09-19-2006 06:24 AM

09-20-2005, 02:04 PM	#1
87mk3moneypit Stock Join Date: Mar 2005 Posts: 15	the engine is almost all the way back together. The head, turbo, flywheel are on. I don't have any of the bolts for the pressure plate, bellhousing, or any of the connecting brackets

09-20-2005, 08:22 PM	#2
rnoswal Lexus & 550's Join Date: Apr 2005 Location: Bossier City LA Posts: 556	Oh well then..................those bolts are easy to find on any other Toyota in the junkyard. The bolts that hold the pressure plate are all the same, 12 mm head, about 3/4 of an inch long. The brackect on the sides are the same as any other front engine rear drive Toyota. They are all 14 mm heads about an inch to an inch and a half long. The bell housings are also 14 mm heads but about 3 inches long. My Supra has the 14 mm head bolts while my 22R 4 cylinder used the 17 mm head sized bolts to hold the bell housing together, never had either one break, but just seemed odd. The bolts holding the trans mount to the frame where just 12 mm heads on the supra and the ones to the trans had 14 mm heads. The nuts on the lower side if the engine mounts were 19 mm heads and the bolts that held the motor brackets to the block were all 14 mm heads 3/4 to 1 inch in length. Hope that helps some, Russ

09-21-2005, 01:42 AM	#3
87mk3moneypit Stock Join Date: Mar 2005 Posts: 15	which is beter the chilton's or the Haynes