checking out an 86 mk3 tomorrow

cre · 01-02-2010, 09:33 PM

As long as it's all zero'd out you should land pretty close to 0* of advance with the distributor bolted in the center of it's range. Unless you're off a tooth or more on a gear there's no room in the adjustment slide to be off more than 15*... I really don't see the point in this.

cvbikeguy · 01-02-2010, 09:41 PM

Quote:

Originally Posted by cre

As long as it's all zero'd out you should land pretty close to 0* of advance with the distributor bolted in the center of it's range. Unless you're off a tooth or more on a gear there's no room in the adjustment slide to be off more than 15*... I really don't see the point in this.

so all i need to do is set everything to 0.

the cams are already lined up with the crank. but for the dist. this hash mark has to be pointing up also?

oregonjoe · 01-02-2010, 09:58 PM

Put crank at TDC of Compression Stroke (if valve covers are off this easy to see when intake valve has rotated and closed)

If everthing is back together you will remove #1 spark plug and put wodden dowel or long straw into cylinder and rotate engine till it tops out and TDC mark on crank.

Then with #1 spark terminal marked on Distrib housing. Put distrib back in and note center of rotor blade aligned with mark. If not aligned, lift out distrib half way till you can rotate the rotor one nothch on the gear teeth and slide all the way back down and recheck. Keep doing this one tooth at a time till you get he rotor blade centered on the #1 spark terminal.

Then set distrib half way on it adjustment travel and tighten down. Recheck by rotationg crank and note if rotor alwys aligns with #1 termianl on cap.

cvbikeguy · 01-02-2010, 10:01 PM

thanks everyone. well sadly i got to go to a funeral now. ill finish up later

cre · 01-02-2010, 10:08 PM

I redo it until the bolt goes through the center WITH the rotor still at 0.

cre · 01-03-2010, 04:48 AM

Did you read my extended post a few posts back? I'm curious, did you install studs or bolts?

cvbikeguy · 01-03-2010, 05:30 AM

Got head arp bolts.

So I know you guys told me pretty blak and white how to put the alternator in but I'm still a little unsure and my dad is just as slow as me.

01-02-2010, 09:58 PM	#3
oregonjoe 3" Exhaust Join Date: Aug 2009 Location: Southern Oregon Coast Posts: 83	Timming Put crank at TDC of Compression Stroke (if valve covers are off this easy to see when intake valve has rotated and closed) If everthing is back together you will remove #1 spark plug and put wodden dowel or long straw into cylinder and rotate engine till it tops out and TDC mark on crank. Then with #1 spark terminal marked on Distrib housing. Put distrib back in and note center of rotor blade aligned with mark. If not aligned, lift out distrib half way till you can rotate the rotor one nothch on the gear teeth and slide all the way back down and recheck. Keep doing this one tooth at a time till you get he rotor blade centered on the #1 spark terminal. Then set distrib half way on it adjustment travel and tighten down. Recheck by rotationg crank and note if rotor alwys aligns with #1 termianl on cap.

01-02-2010, 10:01 PM	#4
cvbikeguy 3" Exhaust Join Date: Nov 2009 Location: Castro Valley, CA Posts: 248	thanks everyone. well sadly i got to go to a funeral now. ill finish up later __________________ 86 MKIII Supra East Bay, CA 7mge rebuild. http://www.toyota-supra.info/forums/...-tomorrow.html MKIII commercial http://www.youtube.com/watch?v=HY9W3...om=PL&index=27 lightening build http://www.toyota-supra.info/forums/...ing-build.html

01-02-2010, 10:08 PM	#5
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	I redo it until the bolt goes through the center WITH the rotor still at 0. __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

01-03-2010, 04:48 AM	#6
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Did you read my extended post a few posts back? I'm curious, did you install studs or bolts? __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

01-03-2010, 05:30 AM	#7
cvbikeguy 3" Exhaust Join Date: Nov 2009 Location: Castro Valley, CA Posts: 248	Got head arp bolts. So I know you guys told me pretty blak and white how to put the alternator in but I'm still a little unsure and my dad is just as slow as me. __________________ 86 MKIII Supra East Bay, CA 7mge rebuild. http://www.toyota-supra.info/forums/...-tomorrow.html MKIII commercial http://www.youtube.com/watch?v=HY9W3...om=PL&index=27 lightening build http://www.toyota-supra.info/forums/...ing-build.html

01-02-2010, 09:33 PM	#1
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	As long as it's all zero'd out you should land pretty close to 0* of advance with the distributor bolted in the center of it's range. Unless you're off a tooth or more on a gear there's no room in the adjustment slide to be off more than 15*... I really don't see the point in this. __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Lower Ball Joints - Checking here first	Grandavi	MKIII Supra	3	09-20-2008 04:04 AM
Picking up my 89 tomorrow	8uwav6	Show n Tell	2	03-31-2008 08:08 PM
Checking Thermostat	scruffboy	Non-Generation Specific Questions	6	03-09-2006 05:49 PM
Supra Noob checking in from Florida	PalmCoastMk3	Non-Generation Specific Questions	1	12-23-2005 05:08 PM
Supra Newb Just checking in	Razor	Non-Generation Specific Questions	1	12-21-2005 04:15 AM