Forum: MKIII Supra
04-12-2009, 03:25 AM
|
|
Replies: 3
Views: 6,811
That last guy was correct. The wires you are...
That last guy was correct. The wires you are looking at are the heater wires for the defrost. I'll bet that you'll need to purchase another rear wiper motor. Water and moisture collects in that...
|
|
Forum: Show n Tell
04-06-2009, 05:03 AM
|
|
Replies: 4
Views: 6,083
|
|
Forum: MKIII Supra
04-05-2009, 08:11 PM
|
|
Replies: 83
Views: 37,995
|
|
Forum: MKIII Supra
04-05-2009, 07:57 PM
|
|
Replies: 83
Views: 37,995
Looks like the exhaust will be a tight fit on...
Looks like the exhaust will be a tight fit on both sides. I'm purchasing a set that I think will work with the space given. Should clear the steering linkage on the drivers side and miss the...
|
|
Forum: MKIII Supra
04-05-2009, 04:33 AM
|
|
Replies: 7
Views: 4,929
|
|
Forum: MKIII Supra
04-05-2009, 04:30 AM
|
|
Replies: 1
Views: 2,359
|
|
Forum: MKIII Supra
04-04-2009, 02:30 PM
|
|
Replies: 6
Views: 2,858
Looks like the plug in for the temperature...
Looks like the plug in for the temperature sensor. If indeed that is what it is, it's for your temp gauge on your dash. The Temp Gauge let's you know the temperature of your engine. You don't want...
|
|
Forum: MKIII Supra
04-04-2009, 02:17 PM
|
|
Replies: 11
Views: 6,103
|
|
Forum: MKIII Supra
04-04-2009, 04:47 AM
|
|
Replies: 83
Views: 37,995
|
|
Forum: MKIII Supra
04-03-2009, 04:01 AM
|
|
Replies: 11
Views: 6,103
|
|
Forum: MKIII Supra
04-02-2009, 07:26 AM
|
|
Replies: 1
Views: 3,110
|
|
Forum: MKIII Supra
04-02-2009, 03:41 AM
|
|
Replies: 11
Views: 6,103
Hope I'm helping.....
What sensor tells the computer when to give the coils a signal on the motor you have installed? Is it a cam position sensor? A Crank sensor? Check for proper voltage out at that location with the...
|
|
Forum: MKIII Supra
03-31-2009, 08:05 AM
|
|
Replies: 83
Views: 37,995
Steel motor plates loosely fitted
Here are a couple pictures of the plates that will be used. The engine mounts will be bolted or welded to these plates. The plates will also be welded to the frame rails.
VT247
|
|
Forum: MKIII Supra
03-31-2009, 07:59 AM
|
|
Replies: 11
Views: 6,103
|
|
Forum: MKIII Supra
03-31-2009, 03:54 AM
|
|
Replies: 11
Views: 6,103
Test for voltage at the coil. If there is no...
Test for voltage at the coil. If there is no voltage going in to the coil, there obviously won't be any spark coming out. Pull off the distributor cap, is the rotor in place?
Best way to test...
|
|
Forum: MKIII Supra
03-29-2009, 11:26 PM
|
|
Replies: 83
Views: 37,995
|
|
Forum: MKIII Supra
03-26-2009, 05:06 AM
|
|
Replies: 2
Views: 3,186
A few quick ideas and I'm not trying to sound...
A few quick ideas and I'm not trying to sound like some smart a$$.
1. Check the fluid level and if it has a filter installed.
2. Make sure the linkage is installed between the transmission...
|
|
Forum: MKIII Supra
03-24-2009, 11:56 AM
|
|
Replies: 83
Views: 37,995
Youtube videos
Here is a video I posted on Youtube.com of the Supra project.
VT247
http://www.youtube.com/watch?v=k2QtXIKyXH8
|
|
Forum: MKIII Supra
03-21-2009, 02:49 AM
|
|
Replies: 83
Views: 37,995
|
|
Forum: MKIII Supra
03-21-2009, 02:44 AM
|
|
Replies: 83
Views: 37,995
Engine test fit is a success
The engine is in and has been test fitted. Goes in like it was made for it. Only had to cut a small hole on the passenger side for the transmission to fit in good. My assumption of using two seperate...
|
|
Forum: MKIII Supra
03-20-2009, 04:56 AM
|
|
Replies: 83
Views: 37,995
Almost done masking it off
Almost finished masking the car off. Did a quick rattle can paint spray to the nose just to give me an idea what it'll look like once I'm finished. Need to mask off the back glass on both sides....
|
|
Forum: MKIII Supra
03-16-2009, 01:23 AM
|
|
Replies: 83
Views: 37,995
|
|
Forum: MKIII Supra
03-15-2009, 03:35 AM
|
|
Replies: 83
Views: 37,995
Here's a picture of the nearly completed...
Here's a picture of the nearly completed interior. Still needs cleaned and the carpet strip. Gauges have been mounted and lines ran through the transmission tunnel. Temp Sensor and Oil Pressure line...
|
|
Forum: MKIII Supra
03-12-2009, 03:32 AM
|
|
Replies: 83
Views: 37,995
Yea, it wasn't meant to be perfect. Taking all...
Yea, it wasn't meant to be perfect. Taking all that stuff off takes time and I wasn't striving to be meticulous. Just wanted it to look better than before. I'm fairly pleased with the results and...
|
|
Forum: MKIII Supra
03-11-2009, 02:58 AM
|
|
Replies: 83
Views: 37,995
Engine bay is done. Paint is on and it looks...
Engine bay is done. Paint is on and it looks infinitely better than the mess that it once was. Going to let that dry for a day or 2 then position the engine / tranny down in.
The shifter is...
|
