maneul conversion ?s

Jeff_5_7 · 12-25-2006, 11:17 PM

how do you put in the cltuch pedal and switch the brkae pedal i really need help with this it would help yall could put some pics of it and how to does the cltuch pedal just bolt in ? thanx

tone loc · 12-25-2006, 11:51 PM

for the brake pedal there is a 14mm nut and bolt. i found it was easier to take the black box off that is right above the steering coloum (a 10 or 12mm bolt dont forget how this goes on.) once that is off you be able to use a rachet, extender, and 14mm socket. fit that on one bolt and then use a 14mm wrench. it might be a bit of a nuckle buster.

for the clucth pedal you need the bracket as well. if you look under the hood in the driver side corner you will see 3 holes 2 small ones for bolts and one larger one. when you have all the clucth lines set up you will be able to put in the master cylinder. you put it in place and then go under the dash and put up the clucth pedal bracket and put on the nuts and bolts and your done.

Jeff_5_7 · 12-26-2006, 12:09 AM

also there is a little silver box next to where the brake pedal goes that says 7mge it is right i nthe way of where i need ot put the clutch any idea what this is and if ican move it to put my clutch pedal in ( my car has a sunroof and for some reason i think it might have ot do with trhe sun roof)

tone loc · 12-26-2006, 12:17 AM

im not sure what that would be. there are like rubber plugs for those holes.

Jeff_5_7 · 12-26-2006, 01:23 AM

hi. my name is kenny i am jeffs older brother . i have changed the slave cylinder on a stand. supra befor and know exctaly what you went threw in in your pictures. i only have one question the auto wont start unless its in Drive or nuetral. and the manual has that little switch the petal pushes in when the push the pedal to the floor. i know a way to jump it and make it work i was just woundering what you did on you car.
thanks for all your info its been a big help.

justin1642 · 12-27-2006, 01:20 AM

i was wondering the same thing on how to get the car to start after switching it from auto to manual. what do you have to do?

tone loc · 12-27-2006, 06:08 PM

i didnt get a chance to finish mine but i dont think you nedd to wire up the pedal to get the car to start. you just wont be able to use cruise and you have to rember to push the pedal in when starting your car. you will have wire up the trans though so the tail lights will work and all that stuff.

Jeff_5_7 · 12-27-2006, 06:26 PM

ok do u no of any way to hook up the pedal becasue u use my cruise a lot and will need it by the way y didnt u finish yours?

12-25-2006, 11:51 PM	#2
tone loc 20psi boost Join Date: Jun 2006 Location: Chicago Posts: 706	for the brake pedal there is a 14mm nut and bolt. i found it was easier to take the black box off that is right above the steering coloum (a 10 or 12mm bolt dont forget how this goes on.) once that is off you be able to use a rachet, extender, and 14mm socket. fit that on one bolt and then use a 14mm wrench. it might be a bit of a nuckle buster. for the clucth pedal you need the bracket as well. if you look under the hood in the driver side corner you will see 3 holes 2 small ones for bolts and one larger one. when you have all the clucth lines set up you will be able to put in the master cylinder. you put it in place and then go under the dash and put up the clucth pedal bracket and put on the nuts and bolts and your done. Attached Thumbnails

12-26-2006, 01:23 AM	#5
Jeff_5_7 3" Exhaust Join Date: Sep 2006 Location: Texas Posts: 109	88 supra auto to 5 speed swap. hi. my name is kenny i am jeffs older brother . i have changed the slave cylinder on a stand. supra befor and know exctaly what you went threw in in your pictures. i only have one question the auto wont start unless its in Drive or nuetral. and the manual has that little switch the petal pushes in when the push the pedal to the floor. i know a way to jump it and make it work i was just woundering what you did on you car. thanks for all your info its been a big help.

12-27-2006, 01:20 AM	#6
justin1642 3" Exhaust Join Date: Mar 2006 Location: Michigan Posts: 213	i was wondering the same thing on how to get the car to start after switching it from auto to manual. what do you have to do? __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Starting problem - Gas conversion ???	eggybread	MKIII Supra	9	12-11-2008 01:48 PM
7MGTE-7MGTEU conversion guide?	ravenmaster	MKIII Supra	1	02-17-2008 01:17 AM
Flip headlight conversion?!?!	dannydavi	MKIII Supra	3	03-18-2007 12:25 PM
Conversion or no conversion??	91 Supra	MKIII Supra	1	06-17-2006 03:39 PM
celica supra engin conversion	supramadness	MKII Supra	3	04-10-2006 12:00 AM

12-25-2006, 11:17 PM	#1
Jeff_5_7 3" Exhaust Join Date: Sep 2006 Location: Texas Posts: 109	how do you put in the cltuch pedal and switch the brkae pedal i really need help with this it would help yall could put some pics of it and how to does the cltuch pedal just bolt in ? thanx

12-26-2006, 12:09 AM	#3
Jeff_5_7 3" Exhaust Join Date: Sep 2006 Location: Texas Posts: 109	also there is a little silver box next to where the brake pedal goes that says 7mge it is right i nthe way of where i need ot put the clutch any idea what this is and if ican move it to put my clutch pedal in ( my car has a sunroof and for some reason i think it might have ot do with trhe sun roof)

12-26-2006, 12:17 AM	#4
tone loc 20psi boost Join Date: Jun 2006 Location: Chicago Posts: 706	im not sure what that would be. there are like rubber plugs for those holes.

12-27-2006, 06:08 PM	#7
tone loc 20psi boost Join Date: Jun 2006 Location: Chicago Posts: 706	i didnt get a chance to finish mine but i dont think you nedd to wire up the pedal to get the car to start. you just wont be able to use cruise and you have to rember to push the pedal in when starting your car. you will have wire up the trans though so the tail lights will work and all that stuff.

12-27-2006, 06:26 PM	#8
Jeff_5_7 3" Exhaust Join Date: Sep 2006 Location: Texas Posts: 109	ok do u no of any way to hook up the pedal becasue u use my cruise a lot and will need it by the way y didnt u finish yours?