Replacing the Head Gasket

[Roger UK]

Well it is quite a daunting job . . . . a few years ago I did the HG myself a couple of times on a V6 Carburettor engine . . . that wasn't too bad. But remember this is a 24 Valve Double overhead camshaft engine with fuel injection . . and loads of vacuum lines and electrical sensors! Plus, even more if you have a Turbo model . .

I got one of the most experienced guys in the UK on these engines to replace my head . . and it still took him about ten hours, even with my help. And unlike most jobs that you've seen someone else do, I WOULDN'T attempt it myself now!

Knowing how expensive your US garages are, that $1,100 quote doesn't sound bad . . . but maybe you can find an enthusiastic amateur who has worked on similar engines to help you.

Having said all that, if the job is done properly there is no problem with stock HG and stock head bolts, as long as it's torqued to 72 ft-lbs (the bolts work loose with original spec) . . . mine has done 10,000 miles since head replaced with no problems.

[rnoswal]

I think we should ask suprra_girl to show us that video where she is under the hood and working on the engine. She seems to know her way around bolts and nuts!.....lol


Russ

[ddmcse]

it's not nearly as difficult as you think
a boat load of bolt and nuts keep track of em !

hardest part i thought was removing the turbo water inlet and oil inlet under the turbo and the egr assembly on the intake side

what video or suprra_grl ?

[suprra_girl]

if you are doing a mhg you need to have the block prepped for it also
you have pretty much the right plan
arp head studs = 82ft lbs
arp head bolts = 72ft lbs
new stock bolts = 72ft lbs

head machined to a fine polish/RA

what are you planning to do with the car

if you're not planning more than 15psi & 300whp then a stock head gasket and arps will be fine and you will get away with having to have a perfect block finish

[SupraDietrich]

I plan on running around 300 HP for a while (well up to 300 anyways) untill after university cause i know i won't have alot of money, but yeah even posting this the same questions still remain, can i do this myself with a few friends ?, cause anything over 1000 bucks just sounds rediculous, i mean i know i will get a torque wrench first thing and get those torque specs set properly to avoid this but even if i just want a batter HG on there like the steal HKS one and some ARP studs with that to make sure this is super reliable then i don't want to pay 2K to get it put on, and remember i'm in canada lol... OH! and does winter driving effect the HG at all ?, like the cold weather and started it in winter... stuff like that, i really want to know this inside and out so i know what to aim for first offf when i buy the car, cause right after all this HG stuff i'm gunna throw 3" downpipe and straight pipe with a nice loud muffler on there MWAHAHAHAHA!!!!, yeah i like my friends 87 turbo, sounds nice, with the straight pipe 3" the whole way, anyways, if anyone can keep posting info on the HG stuff and pictures videos links to step by step repair (do-it-yourself) sites, pretty much anything cause i kinow alot will benefit from this if i can get a few experienced enthusiasts to give us their best info about it, thanx again, Dieter

[Bullz_EyE]

Originally Posted by suprra_girl

head machined to a fine polish/RA

Whats the "RA" stand for?

EDIT: You also mentioned you need the block prepped. What on the block needs to prepped for a MHG?

[Bullz_EyE]

Bump for a response.

[mrnickleye]

Originally Posted by Bullz_EyE

Whats the "RA" stand for?

EDIT: You also mentioned you need the block prepped. What on the block needs to prepped for a MHG?

It means way more work and $$$.....stick to head work and stock gaskets.
The block would need to come out and stripped down and sent to machine shop for a resurface to a near mirror finish. Only needs to be done when you are trying to increase HPs over 300-350. Wait till you've owned it a long while, and feel like making it your hobby (throw $$$$ at) car.