Manual transmission, INsTALL(jacking it up)

[87hilux7mge]

get the clutch properly bled then come back and let us know what its doing. improperly bled clutches suck and they make everything feel wrong especially with air in the line.

[ochowdero]

Originally Posted by 87hilux7mge

get the clutch properly bled then come back and let us know what its doing. improperly bled clutches suck and they make everything feel wrong especially with air in the line.

i was talking to #btwilson and he asked if i bench bled the master cylinder
which i did not do,
the system when i would bleed it would have a full stream come out but for some reason it still happens...
ima bench bleed both my master and slave cylinder to see if that solves it..

i did bleed it properly just didnt know i needed to prime the master cylinder before i hooked it up and bled the system like normal

[ochowdero]

whats this?







lol i over filled my trans mostlikely cuz i wasnt exact on the amount
5.2 pints, 2.6 quarts

so i put three quarts in thinking it may have been wrong info...
car wasnt all to level but it was level enough to get a reading..

so i went and bled my clutch and got pissed at the free play that i had so i decided to test drive it,
it was alil hard to get into first and second but the rest were smooth sailing..
then i park in my drive way and trans started leaking at the tail shaft out of the driveshaft (tail shaft right?)
(this is where i knew i over filled it) so yada and whatever car runs fine but gott tweak the clutch...
i went to my gf house, clutch was still alil soft and kinda hard to shift but i got there and parked, but transmission started leaking again... soo
i just let it leak, becuz i knew i put to much in. before i drove home i pulled my carpet back and was able to use the clutch correctly( still gotta tweak it, i cant drive around with my carpet back...any ideas of to whats wrong?) i get home and park, and it started leaking again, but not as much as at my gfs house.. so i pull into my garage to where its level and the trans is fine, no leaking but just dripping the excess off the mount..
now im sitting down thinking..
the part in the pics, my mechanic said i dont need it and that if i wanted to i can put it in to be safe... it goes in wear my driveshaft goes, im starting to think that it is needed OR somewhat needed... i have no clue what it is..
i just know its a retainer of some sort...
now that you know my story of what happen today about my car, can you give me some insight of what this is and if its needed?
IM STARTING TO THINK IT IS!

[87hilux7mge]

ok. i hate to be mean, but you need to stop driving your car with just base knowledge slammed at it. the seal you have in your pics is prolly a rear tranny seal, and from the sound of it youve been puking fluid out of it. you obviously overfilled it, and thats where all the leaks have been coming from..

just slow down and stop jumping the gun. you need to give us all more info on whats goin on than what youve been doing, cuz were only getting half the story.

so, u over filled..what else. just take it slow and explain whats happening.

[ochowdero]

Originally Posted by 87hilux7mge

ok. i hate to be mean, but you need to stop driving your car with just base knowledge slammed at it. the seal you have in your pics is prolly a rear tranny seal, and from the sound of it youve been puking fluid out of it. you obviously overfilled it, and thats where all the leaks have been coming from..

just slow down and stop jumping the gun. you need to give us all more info on whats goin on than what youve been doing, cuz were only getting half the story.

so, u over filled..what else. just take it slow and explain whats happening.

i put transmission fluid in.
tried bleeding it and didnt work..
then tried a "Bench bleed" on my master cylinder and it worked alil just gotta adjust it and get it perfectly bled..i did that so i can shift to get it to my shop(a mile up the street)
tomorrow regardless, im taking it to the shop to have my mechanic properly bleed my system...
like i just said when i pulled back my carpet i was able to used the clutch properly because it fully disengaged, SO I NEED TO ADJUST IT, SO ITS LIKE ITS SPOSE TO BE.

so back to the tranny, i put 3 quarts in, i know that is an over fill... so that goes to why im leaking...
i need to know if that "seal" is needed in my trans and if i can drive without it, to get my clutch bled properly..or even drive without it or what the heck it is and for. i dont mind going back under the car and replacing it but i need to know what it is, and if its needed or not.


and like i said, it only leaks after driving it..
idk why(besides overfill)

" i hate to be mean, but you need to stop driving your car with just base knowledge slammed at it"
what do you meen by that?

[87hilux7mge]

i mean stop trying to drive it till u have gone through a basic mechanical checklist of things that need to be fixed. otherwise youll ruin something and have to do this all over again.

i.e.-your clutch system needs a proper bleed.

you also need to trim your carpet or trans tunnel some to get full shifter travel, as that sounds like whats stopping you from getting it into gear properly.

you also probably need to replace the output shaft seal on the tranny if its constantly puking fluid out after driving. its building up pressure inside the tranny and forcing fluid out.

my question is, why did you overfill the tranny to begin with?

so. get the clutch system figured out. theres only a few parts to it that can go bad. master cyl, slave cyl, hydraulic line. check any and all for leaks, and if it comes down to it, replace them. slave cyls go out all the time, so check there if its not new. master cyls are less common but ive had them go too.

next, put a new rear seal on the tranny and take the fill plug out of the side of the tranny and let it drain till the fluid is leveled off (be on a flat, level piece of ground for this).

adjust/trim your carpet/trans tunnel so you get proper shifter throw.

after youve done all that, check back.

[ochowdero]

MasteR cylinder is brand new as well as the slave, the lines however aren't, should I replace the hardlines?

[ochowdero]

my turn signals dont work either!
help i need those lol
tired of sticking my dam hand out the window!

[ochowdero]

the retainer or seal,
i need to replace it
i checked the tsrm and dont know where to look..
anyone have the proper name for this and the product number?
i need to replace asap
and also
how to replace it?
please and thank you

(if you can point me to the how to on the tsrm then thatll be ok to)

[ochowdero]

i bought the seal... how do i replace it ?