1986 1st Supra Running Poorly

dlfred · 03-19-2010, 12:17 PM

Have everything out of the way and was able to plug in the KS. Now I have to be able to check the vacuum line routing and connections. I guess I can understand the lack of clean up for a flat rate mech, but man it sure was nasty in there. What causes that much intake goo? It looked like mud/grease all though the intake plenum and box. It is now much cleaner.
There is a small 2 hole bracket with vacuum line hook ups, on the drivers side below the intake. Any ideas on what those 2 bolt holes line up too? This thing has been good to work on so far. Thanks

cre · 03-20-2010, 12:21 AM

http://www.cygnusx1.net/Supra/Librar...spx?F=1708&P=2

dlfred · 03-20-2010, 09:09 PM

There is a broken wire on one of the connectors, VSV I think the filter is broke of it and now there isn't a bit of wire to repair the connector.

As far as the broken wire, I was thinking that I could take a straight pin and connected the wire and connector using the pin in the center and solder the area. Sounds pretty cheap, I haven't figured out how to push the remaining wire out of the connector and go at it that way. I am open to suggestions, please.

thanks

03-20-2010, 12:21 AM	#2
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	http://www.cygnusx1.net/Supra/Librar...spx?F=1708&P=2 __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

03-20-2010, 09:09 PM	#3
dlfred 3" Exhaust Join Date: Mar 2010 Location: Georgia Posts: 66	There is a broken wire on one of the connectors, VSV I think the filter is broke of it and now there isn't a bit of wire to repair the connector. As far as the broken wire, I was thinking that I could take a straight pin and connected the wire and connector using the pin in the center and solder the area. Sounds pretty cheap, I haven't figured out how to push the remaining wire out of the connector and go at it that way. I am open to suggestions, please. thanks Attached Thumbnails Last edited by dlfred; 03-21-2010 at 06:15 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
HELP PLEASE	Nick0887	Non-Generation Specific Questions	4	02-28-2009 07:26 AM
1986 supra problems	brossini	MKII Supra	1	09-18-2008 06:49 AM
Dream Offer	Karma_Supra	MKIV Supra	22	10-17-2007 03:04 PM
MKIV Supra TT Daytime Running Lights??	MIX	MKIV Supra	2	08-30-2007 02:52 AM
supra running rough	finn	MKIII Supra	0	09-25-2006 07:10 PM

03-19-2010, 12:17 PM	#1
dlfred 3" Exhaust Join Date: Mar 2010 Location: Georgia Posts: 66	Have everything out of the way and was able to plug in the KS. Now I have to be able to check the vacuum line routing and connections. I guess I can understand the lack of clean up for a flat rate mech, but man it sure was nasty in there. What causes that much intake goo? It looked like mud/grease all though the intake plenum and box. It is now much cleaner. There is a small 2 hole bracket with vacuum line hook ups, on the drivers side below the intake. Any ideas on what those 2 bolt holes line up too? This thing has been good to work on so far. Thanks