Forum: MKIII Supra
06-15-2011, 04:40 AM
|
Replies: 3
Views: 2,525
Thanks ill check out those options out it also...
Thanks ill check out those options out it also misses during low rpm when i try to open up the throttle, and has trouble idleing so I think the tps could atleast be causing that irs throwi ng tps code
|
Forum: MKIII Supra
06-15-2011, 02:37 AM
|
Replies: 0
Views: 1,331
valve clearence.
Ok 89 supra turbo. head decked, but i dont know how much cuz it was done before i bought the head. also had the block decked but dont know how much on that either. how can i go about making sure my...
|
Forum: MKIII Supra
06-15-2011, 01:59 AM
|
Replies: 3
Views: 2,525
dead cylinder miss
89 supra turbo with T61 turbo upgrade, 550cc injectors, 3 inch turbo back exhaust, Apexi SAFC, just fully rebuilt it, rod and main bearings, pistons rings, the works, i think it needs a TPS, so that...
|
Forum: MKIII Supra
06-05-2011, 08:22 PM
|
Replies: 8
Views: 4,263
|
Forum: MKIII Supra
06-05-2011, 05:48 AM
|
Replies: 8
Views: 4,263
|
Forum: MKIII Supra
06-03-2011, 09:58 PM
|
Replies: 8
Views: 4,263
Ok so I could pull the wire diagram for the ecu...
Ok so I could pull the wire diagram for the ecu and trace the grounds back from there to make sure I got them all hooked up? And also do they havent to be grounded on the engine or coulson they be...
|
Forum: MKIII Supra
06-03-2011, 08:25 PM
|
Replies: 8
Views: 4,263
|
Forum: MKIII Supra
06-03-2011, 06:21 PM
|
Replies: 8
Views: 4,263
rebuilt 7mgte problems
Ok i just dropped my engine back into my 89 supra 5-speed turbo.
, its a 7mgte with a t61 turbo, 550cc RC injectors, 3 inch turbo back exhaust, Apexi super air flow converter, and i think the MAF...
|
Forum: MKIII Supra
04-03-2011, 04:39 AM
|
Replies: 8
Views: 5,297
|
Forum: MKIII Supra
04-01-2011, 12:46 AM
|
Replies: 8
Views: 5,297
|
Forum: MKIII Supra
03-31-2011, 11:35 PM
|
Replies: 8
Views: 5,297
Rod bearing size
Hello, im rebuilding my 1989 turbo supra, its torn down to nothing but the block and the crank because im not replacing the mail bearings or turning the crank because there was no damage to any of...
|
Forum: MKIII Supra
03-19-2011, 12:48 AM
|
Replies: 2
Views: 2,228
Oem head bolts
Where can i get a set of OEM head bolts with the factory Allen wrench bolt heads? i dont like the ARP studs cuz i had an issue with my old 7mge that i could not get the nuts back off the studs....
|
Forum: MKIII Supra
03-14-2011, 10:46 PM
|
Replies: 0
Views: 1,227
Found my problem
3821
Dropped two valves, destroyed the head on that cylinder, and destroyed that piston. but im just goin to replace the whole motor cuz there are metal shavings everywhere. Anyone got a 7mgte...
|
Forum: MKIII Supra
03-02-2011, 12:26 AM
|
Replies: 5
Views: 4,545
|
Forum: MKIII Supra
02-28-2011, 03:25 AM
|
Replies: 5
Views: 4,545
|
Forum: MKIII Supra
02-28-2011, 12:03 AM
|
Replies: 5
Views: 4,545
Rod Knock! OR is IT?
My 89 supra was in my garage for a compression test. results were not great, 140,100, 135, 110, 130, 140. So with head in hands i put the coil packs and intake piping and what not back on and fired...
|
Forum: MKIII FAQ
02-21-2011, 05:32 AM
|
Replies: 226
Views: 123,351
|
Forum: MKIII Supra
02-20-2011, 06:28 PM
|
Replies: 4
Views: 2,500
|
Forum: MKIII Supra
02-20-2011, 06:19 AM
|
Replies: 2
Views: 1,967
BHG symptoms
Sorry i know i have been blowing you guys up lately lol but yet another question.
I have a small yet troublsome oil leak near the turbo on my car, really only notice it at idle after a hard pull,...
|
Forum: MKIII Supra
02-20-2011, 06:06 AM
|
Replies: 3
Views: 1,821
i usualy have the head decked and i use an...
i usualy have the head decked and i use an aluminum safe pad on an air grinder for the block, i figure since is safe to use on aluminum it should not hurt the cast iron block at all right?
|
Forum: MKIII Supra
02-20-2011, 06:04 AM
|
Replies: 4
Views: 2,500
|
Forum: MKIII Supra
02-20-2011, 02:02 AM
|
Replies: 4
Views: 2,500
7mgte engine wire harness
I am in serious need for an engine wire harness for my 89 supra turbo. does anyone have one or know where they can be bought. i have checked all my local scrap yards and i know they no longer sell...
|
Forum: MKIII Supra
02-18-2011, 10:16 PM
|
Replies: 3
Views: 1,821
Head Gasket recomendations.
Blow head gasket!! of course i cant get a supra that does not blow a head gasket lol so what brands would you guys recomend for standing up do around 10-15psi of boost? what thickness? any direct...
|
Forum: MKIII Supra
02-17-2011, 04:19 AM
|
Replies: 11
Views: 3,296
|
Forum: MKIII Supra
02-16-2011, 09:27 PM
|
Replies: 10
Views: 7,878
ver nice way to explain that lol that makes...
ver nice way to explain that lol that makes since. what are the odds of a crack in my intercooler? its factory, and i had an air pocket in the coolent system so it was pushing all my coolent out of...
|