05-24-2010, 08:19 PM
|
#1 |
|
Stock
Join Date: May 2010
Location: anaheim
Posts: 3
 |
Engine harness question between auto and manual
Hi,
I purchased a 2jzgte swap that comes with a manual tranny detached. There is however an auto flywheel that is attached to the engine. And I believe the engine harness must be automatic? The swap did not come with any ECU. My question is.. is there any difference between an auto and manual engine harness? Will an auto ECU and a manual ECU fit the connector on the engine harness just fine? Will there be any modification required? Please help answer my question. Thank you. |
|
|
|
05-25-2010, 03:00 AM
|
#2 | |
|
Supra Owner
Join Date: Oct 2005
Location: GA, USA
Posts: 2,209
|
Quote:
If you want to modify an auto tranny to adapt to a manual transmission, then yes it would have to be modified - due to the differing transmission connectors.
__________________
Phil '94 Supra Turbo, 6spd, 'APU'+ Displacement is no replacement for boost. Life begins at 30psi. NB: Please consider posting any help requests in a new thread instead of asking me for help privately. About 99.9+% of the time, private help requests end up covering great information that could be very valuable to other forum members. If you have a good reason for needing the help request to be private, I'll consider it. If not, then why not give everyone else the opportunity to pitch in too, and/or learn from the information? Remember, there's no such thing as a dumb question. We're all here to help within this family of Supra owners. |
|
|
|
|
|
05-25-2010, 03:58 AM
|
#3 |
|
Stock
Join Date: May 2010
Location: anaheim
Posts: 3
|
Hi,
Are you saying the connectors on the harness differ between an auto and manual setup in term of sensors? but then you're saying the connector that connects to the ECU is identical, regardless if it's an automatic or manual engine harness, correct? So for example if I have an automatic engine (with an automatic engine harness lets say), and if I were to connect a manual ECU it would fit the connector on that harness? Sorry for asking so many questions. i just need some clarification that's all. Thanx |
|
|
|
|
05-25-2010, 04:22 AM
|
#4 | |
|
Supra Owner
Join Date: Oct 2005
Location: GA, USA
Posts: 2,209
|
Quote:
Yes, the ecu connector is identical. Yes, the manual ecu would fit fine with the auto harness, but you wouldn't have the appropriate connectors to plug the auto harness into the manual tranny.
__________________
Phil '94 Supra Turbo, 6spd, 'APU'+ Displacement is no replacement for boost. Life begins at 30psi. NB: Please consider posting any help requests in a new thread instead of asking me for help privately. About 99.9+% of the time, private help requests end up covering great information that could be very valuable to other forum members. If you have a good reason for needing the help request to be private, I'll consider it. If not, then why not give everyone else the opportunity to pitch in too, and/or learn from the information? Remember, there's no such thing as a dumb question. We're all here to help within this family of Supra owners. |
|
|
|
|
|
05-25-2010, 05:34 AM
|
#5 |
|
Stock
Join Date: May 2010
Location: anaheim
Posts: 3
|
Gotcha. Thank you for your help, much appreciated!
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| HELP PLEASE | Nick0887 | Non-Generation Specific Questions | 4 | 02-28-2009 07:26 AM |
| convert supraIV from auto to manual question | turbofreak128 | Non-Generation Specific Questions | 0 | 03-03-2008 10:46 PM |
| auto wiring harness on manual? | mizuboi | MKIII Supra | 0 | 02-22-2007 07:15 PM |
| Engine Harness question | kidsusukigsxr | Non-Generation Specific Questions | 0 | 01-31-2007 05:33 AM |
Linear Mode
