Head gasket repair

Kuban · 07-15-2007, 03:49 PM

Quote:

Originally Posted by plaaya69

I was looking at your Sig and is this your jasper motor with 868 Miles that you are replacing the HG?

yes i have a prior thread if you care to check it out. Jasper will not cover the manufacture defect of the headgasket failure and the ring falure in cylenders 5 and 3. I pulled the head off in about 3 hours (damn iv been doing this too long) found out there are scores on cylender bores 5 and 3. I checked it with an inside-mic and i see about .0023 difference from standard bore. I can easily rebore that in the shop. Its only 23 ten-thou so i might even be able to hone that out. Heres my parts list im going to throw together over the next few weeks.

supramacist · 07-15-2007, 08:04 PM

You'll be glad you got the parts from HPF.

They hot foot those things right the heck over.
I recieved most of my 3 shipments within 2 to 3 days of ordering.

Just remember they are pacific time zone.

Kuban · 07-15-2007, 11:03 PM

Quote:

Originally Posted by supramacist

You'll be glad you got the parts from HPF.

They hot foot those things right the heck over.
I recieved most of my 3 shipments within 2 to 3 days of ordering.

Just remember they are pacific time zone.

Yea iv ordered from them quite a few times. They actually call me once a week to see if i would like to place an order for my supra haha.

Kuban · 07-15-2007, 11:23 PM

Ok i got some pics + some youtube videos of what it looks like now, sorry for poor quality.

http://www.youtube.com/watch?v=uGDRGaGLgI8 VIDEO 1

http://www.youtube.com/watch?v=-BhbuU89qlU VIDEO 2

http://www.youtube.com/watch?v=nwnwPDLn9Yw VIDEO 3

Realisticlly i thought i was taking pics with my pda turns out it was on video mode.

--------------------------------------------------------------------------

PICS

supramacist · 07-16-2007, 04:07 AM

How many Lbs. of torque did you apply to your idle tensioner pulley???

Engine looks good man.

Kuban · 07-20-2007, 09:01 PM

it was a fully assembled long block from jasper. timing belt was already torqed and timed.

07-15-2007, 11:23 PM	#4
Kuban 3" Exhaust Join Date: Feb 2007 Location: Milwaukee, WI Posts: 174	Ok i got some pics + some youtube videos of what it looks like now, sorry for poor quality. http://www.youtube.com/watch?v=uGDRGaGLgI8 VIDEO 1 http://www.youtube.com/watch?v=-BhbuU89qlU VIDEO 2 http://www.youtube.com/watch?v=nwnwPDLn9Yw VIDEO 3 Realisticlly i thought i was taking pics with my pda turns out it was on video mode. -------------------------------------------------------------------------- PICS __________________ -868 Miles on new jasper engine -All hard pipes -0.57 trim ct-26 -greddy type S -greddy profec b -apexi ride high 7 way adjustables -eibach springs -slotted rotors -mkIV TT rims (front)245/45/17 (rear)285/40/17 -targa -greddy turbo timer -egr eliminated -3" turbo back, no cat, no resonator, Apexi N1 back. -n/a cams Theres others ill think of later.

07-20-2007, 09:01 PM	#6
Kuban 3" Exhaust Join Date: Feb 2007 Location: Milwaukee, WI Posts: 174	it was a fully assembled long block from jasper. timing belt was already torqed and timed. __________________ -868 Miles on new jasper engine -All hard pipes -0.57 trim ct-26 -greddy type S -greddy profec b -apexi ride high 7 way adjustables -eibach springs -slotted rotors -mkIV TT rims (front)245/45/17 (rear)285/40/17 -targa -greddy turbo timer -egr eliminated -3" turbo back, no cat, no resonator, Apexi N1 back. -n/a cams Theres others ill think of later.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Blown Head Gasket repair w/pics	IHateHacks	MKIII FAQ	226	02-21-2011 05:32 AM
Blown Head Gasket Snake Oil	unkymurch	Non-Generation Specific Questions	21	08-06-2010 02:11 AM
Head Gasket replacement questions.	DavidLeClair584	MKIII Supra	1	06-09-2007 09:17 PM
Buying a 87, head gasket questions	Gengus	MKIII Supra	1	04-14-2007 07:15 PM
Links to Head Gasket Repair Info	mrnickleye	Supra FAQ	1	02-16-2007 06:44 AM

07-15-2007, 08:04 PM	#2
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	You'll be glad you got the parts from HPF. They hot foot those things right the heck over. I recieved most of my 3 shipments within 2 to 3 days of ordering. Just remember they are pacific time zone.

07-16-2007, 04:07 AM	#5
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	How many Lbs. of torque did you apply to your idle tensioner pulley??? Engine looks good man.