Rebuilding my ct-26

Kuban · 05-30-2007, 04:53 PM

Quote:

Originally Posted by supradaddy0803

I used to be a jet engine mechanic for a living. I would say that for the rebuild kit if it includes a new compressor wheel then your trimmed compressor wheel would have to be saved or get the new one trimmed as well. As for the nut I dont think they make a 18pt or 24pt socket or nut but it might be 12pt. Jet engines are a lot like turbos in a sense and they use a ton of 12pt nuts everywhere. Easier to torque and that kind of stuff. Go to sears and get a set of metric 12pt sockets. If they dont fit may be a SAE never know they are funny sometimes.

thx for the reply. I can tell you for sure its not a 12pt on the compressor wheel. The exhaust turbine is a 12pt 15mm. But the compressor nut has waaay more pt's on it than 12. Im pretty sure someone mentioned it could be an SST from toyo. Although they also said this is what the original nut would be like, not a trimmed up wheel nut. Maybe they resused the original, if they did there goddamn retarded.

supradaddy0803 · 05-30-2007, 05:25 PM

I looked in the tsrm and found a tool for that it is in the one listed on this forum not good at linking. As for that I called the toyo house and it is a expensive tool from what they say. If you lived close my friend actually has one he would let you borrow. From what he said you have to replace that nut becuase he thinks it is self locking and has that bent top to lock it. He said it was a 18pt socket that is part of the T handle that it comes on. At least when you do the rebuild you know who did the work and you know that it was done right.

joebuffalo · 05-30-2007, 07:10 PM

I am also in the process of rebuilding my CT26. The nut you are refering to can be taken off with a 3/8 socket. You just have to tap it on there lightly. My turbo rebuild kit came with a new nut. Here is a link to a website that has some great pictures that may be of some help.

http://www.mybluemr2.co.uk/CT26/index.htm

He is the one that suggests the 3/8 socket

Kuban · 05-30-2007, 08:40 PM

ok thanks man that will help.

only one question left then, can i use a regular ct-26 rebuild kit with my turbo? even though its a t3/t04e .50 trim ct-26. Im assuming yes.

05-30-2007, 05:25 PM	#2
supradaddy0803 12psi boost Join Date: May 2006 Location: Athens, TX Posts: 308	I looked in the tsrm and found a tool for that it is in the one listed on this forum not good at linking. As for that I called the toyo house and it is a expensive tool from what they say. If you lived close my friend actually has one he would let you borrow. From what he said you have to replace that nut becuase he thinks it is self locking and has that bent top to lock it. He said it was a 18pt socket that is part of the T handle that it comes on. At least when you do the rebuild you know who did the work and you know that it was done right. __________________ 1987 supra NA 5 speed 1JZGTE swap Tokico Illumina 2 and Eibach springs Tokico pillow blocks Suspension Techniques front and rear sway bar HKS super dragger cat-back exhaust plus test pipe Greddy Profec B spec 2 boost controller HKS type 1 turbo timer Supra sport solid steel drive shaft Walboro 255 fuel pump JZA70 Front end mod 18" Volk Racing AV3 18x8.5 front 18x9.5 rear

05-30-2007, 08:40 PM	#4
Kuban 3" Exhaust Join Date: Feb 2007 Location: Milwaukee, WI Posts: 174	ok thanks man that will help. only one question left then, can i use a regular ct-26 rebuild kit with my turbo? even though its a t3/t04e .50 trim ct-26. Im assuming yes. __________________ -868 Miles on new jasper engine -All hard pipes -0.57 trim ct-26 -greddy type S -greddy profec b -apexi ride high 7 way adjustables -eibach springs -slotted rotors -mkIV TT rims (front)245/45/17 (rear)285/40/17 -targa -greddy turbo timer -egr eliminated -3" turbo back, no cat, no resonator, Apexi N1 back. -n/a cams Theres others ill think of later.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rebuilding a turbo	90supra	Non-Generation Specific Questions	1	04-28-2008 12:30 PM
Rebuilding a 1993 mkiv	TurboTom	MKIV Supra	1	01-29-2008 05:50 AM
Rebuilding turbo	redmaro	MKIII Supra	5	09-29-2006 11:05 AM
Rebuilding problems (7M-GE)	Matt'sMKIII	MKIII Supra	3	05-09-2006 05:03 PM
Rebuilding 87 7m-gte	Reeves	MKIII Supra	6	04-25-2006 01:10 AM

05-30-2007, 07:10 PM	#3
joebuffalo Stock Join Date: Oct 2005 Location: memphis Posts: 17	I am also in the process of rebuilding my CT26. The nut you are refering to can be taken off with a 3/8 socket. You just have to tap it on there lightly. My turbo rebuild kit came with a new nut. Here is a link to a website that has some great pictures that may be of some help. http://www.mybluemr2.co.uk/CT26/index.htm He is the one that suggests the 3/8 socket