testing the ecu

bignag06 · 09-12-2011, 05:17 AM

the ecu is responding to flash the check engine light and it does not smell like burning electronics. now its giving me a different code, its giving me code 41, which is the throttle position sensor. so my dad went to the junk yard and found a sensor from a toyota cressida and after i did research to make sure it was for a 7mge, it turns out that sensor is for the 5mge, my question is could i still use that sensor on the 7mge?

cre · 09-12-2011, 07:19 AM

Did you test your existing TPS first? I ask because you don't mention it and wiring it just as often the source of that particular code.

Toyota doesn't list the two as cross compatible but they're such a simple component it may work as long as the physical characteristics (size, mounts and deflection angle of the interfacing tabs) and the pin-out are the same. If the physical characteristics match then test the 5M unit with a multimeter to verify that the readings match what are required by the 7M-GE. When connected (and after testing to make sure you're not going to short anything out by even plugging it in) you should see a value of ~.50v on the VTA pin with the throttle closed and a value of ~3.48v with the throttle fully open.

Look at the list HERE for vehicles which used the same TPS. Look at the section for part number "89452-14050" (which should be the same as your original).

09-12-2011, 07:19 AM	#2
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Did you test your existing TPS first? I ask because you don't mention it and wiring it just as often the source of that particular code. Toyota doesn't list the two as cross compatible but they're such a simple component it may work as long as the physical characteristics (size, mounts and deflection angle of the interfacing tabs) and the pin-out are the same. If the physical characteristics match then test the 5M unit with a multimeter to verify that the readings match what are required by the 7M-GE. When connected (and after testing to make sure you're not going to short anything out by even plugging it in) you should see a value of ~.50v on the VTA pin with the throttle closed and a value of ~3.48v with the throttle fully open. Look at the list HERE for vehicles which used the same TPS. Look at the section for part number "89452-14050" (which should be the same as your original). __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
testing and setting the tps on a 1990 n/a supra???	dgee509	MKIII Supra	2	04-16-2011 04:46 PM
Cold Start System Testing (hard starting)	mrnickleye	MKIII Supra	12	11-13-2010 08:32 PM
Testing for bad ECU, &/or bad Fuel Pump	elliotl	MKIII Supra	0	08-21-2007 10:42 PM
improper resistance ohm testing my afm.	DRIFTINGmy85	MKII Supra	1	11-30-2006 08:35 PM

09-12-2011, 05:17 AM	#1
bignag06 Stock Join Date: Aug 2011 Location: compton, ca Posts: 11	the ecu is responding to flash the check engine light and it does not smell like burning electronics. now its giving me a different code, its giving me code 41, which is the throttle position sensor. so my dad went to the junk yard and found a sensor from a toyota cressida and after i did research to make sure it was for a 7mge, it turns out that sensor is for the 5mge, my question is could i still use that sensor on the 7mge?