clutch question

turbonicsperformance · 09-10-2011, 02:05 AM

i have a 7mgte in my miata with cp pistons studded mhg maf-t 3 inch custom dp fmic and 2.5" piping and 550 ccs running 15psi from the "gte-u" turbo (i guess... idk exactly but the compressor wheel is 5mm larger than my friends and another ct26 i have lying around as well as havind 6 dual fins rather than 5) i have the ACT stage 2 street clutch and in 3rd or above under boost it slips quite a bit the pressure plate has good pressure and only like 8k on it... it held up to 6 psi fine when i went to 15 it started slipping and now that it has glazed it slips all the time even lowering it back to 10psi i'm just running a w58 for the time being until i locate a r154 plus the miata only weighs 2360 with me and a FULL tank of gas lol so the w58 should take quite a bit it just spins the tires instead

I found the disc i needed though part # 6236007 6 puck unsprung or 6236207 6 puck sprung

any experience in possible holding gain between the 6 puck and street disc?

09-10-2011, 02:05 AM	#5
turbonicsperformance 3" Exhaust Join Date: Apr 2010 Location: sarasota fl Posts: 194	i have a 7mgte in my miata with cp pistons studded mhg maf-t 3 inch custom dp fmic and 2.5" piping and 550 ccs running 15psi from the "gte-u" turbo (i guess... idk exactly but the compressor wheel is 5mm larger than my friends and another ct26 i have lying around as well as havind 6 dual fins rather than 5) i have the ACT stage 2 street clutch and in 3rd or above under boost it slips quite a bit the pressure plate has good pressure and only like 8k on it... it held up to 6 psi fine when i went to 15 it started slipping and now that it has glazed it slips all the time even lowering it back to 10psi i'm just running a w58 for the time being until i locate a r154 plus the miata only weighs 2360 with me and a FULL tank of gas lol so the w58 should take quite a bit it just spins the tires instead I found the disc i needed though part # 6236007 6 puck unsprung or 6236207 6 puck sprung any experience in possible holding gain between the 6 puck and street disc? __________________ 92 miata 7mgte swap forged pistons,studded mhg, 3 inch dp with a glass pack,blowthrough MAF-T,550cc inj, act stage 2 clutch, fmic kit, greddy rs, full wire tuck, rx7 lsd rear with 4.10s. 15psi "ct26-A"??(waiting on dyno #s) if anyone knows whats up with my turbo let me know it has a larger comp wheel nicer machining and 6 dual fins rather than 5? its confusing and keep finding too much contradicting info. would LLLLLOOOOOOOOVVVVVVVEEEEE a compressor map

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MK III turbo clutch setup question.	DarkSupra2.5	MKIII Supra	5	02-10-2010 05:58 AM
clutch question	a7morelli	MKIII Supra	1	07-18-2009 10:36 PM
Clutch wear question	suprabahamut	Non-Generation Specific Questions	2	09-14-2008 04:20 PM
Clutch Master Cylinder question. 1989 Supra.	PFlanagan	MKIII Supra	4	08-07-2008 08:20 PM
clutch question !!	88Supra86	MKIII Supra	5	09-26-2007 01:47 AM