What do I need to hit 400 whp?

Anthonydi · 01-23-2011, 05:09 AM

Yeah the first thing I ever did to the car aftermarket was I installed an aem uego, as well as a bigger boost and water temp gauge. As far as the mileage goes it currently has 160xxx. I didnt put it on the list but before I up the hp at all I plan to replace all gaskets, seals, hoses, vacum lines, etc. Im not upping the hp at all till I know the engine can handle it I just didnt put it down cause I figured it was common sense lol. What I meant about the methanol injection kit is from my understanding isnt that bad for the internals. Like wont it burn them up or am I far off I dont know alot about methanol injection

turbonicsperformance · 01-23-2011, 01:42 PM

no meth injection is a good thing basically if you run meth with 93 octane its like running c16 or ~116 octane fuel it only comes on at a set boost level and allows you to run more advance in your timing
and when you make sure your engine can hold the power it would be a good idea to replace bearings and piston ring and have the cylinders honed itd be best to go with a better set of pistons also but the rods should be fine

Anthonydi · 01-26-2011, 09:52 PM

Ok and after all that I should be pushing 400

cre · 01-26-2011, 10:13 PM

The Blitz is a crap filter... I'd recommend either an Apex'i or AEM DryFlow (one of the best filters out there in both price and performance). As for what else you'll need there's a lot of over-building going on but that's generally something I'm in favor of, so I've nothing else to add. I will say that I'll take a rebuilt upgrade turbo over a cheap Chinese turbo any day.... you're not going to find a GOOD T4 for anywhere near the same price (not new anyway).

01-23-2011, 01:42 PM	#2
turbonicsperformance 3" Exhaust Join Date: Apr 2010 Location: sarasota fl Posts: 194	no meth injection is a good thing basically if you run meth with 93 octane its like running c16 or ~116 octane fuel it only comes on at a set boost level and allows you to run more advance in your timing and when you make sure your engine can hold the power it would be a good idea to replace bearings and piston ring and have the cylinders honed itd be best to go with a better set of pistons also but the rods should be fine __________________ 92 miata 7mgte swap forged pistons,studded mhg, 3 inch dp with a glass pack,blowthrough MAF-T,550cc inj, act stage 2 clutch, fmic kit, greddy rs, full wire tuck, rx7 lsd rear with 4.10s. 15psi "ct26-A"??(waiting on dyno #s) if anyone knows whats up with my turbo let me know it has a larger comp wheel nicer machining and 6 dual fins rather than 5? its confusing and keep finding too much contradicting info. would LLLLLOOOOOOOOVVVVVVVEEEEE a compressor map

01-26-2011, 10:13 PM	#4
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	The Blitz is a crap filter... I'd recommend either an Apex'i or AEM DryFlow (one of the best filters out there in both price and performance). As for what else you'll need there's a lot of over-building going on but that's generally something I'm in favor of, so I've nothing else to add. I will say that I'll take a rebuilt upgrade turbo over a cheap Chinese turbo any day.... you're not going to find a GOOD T4 for anywhere near the same price (not new anyway). __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

01-23-2011, 05:09 AM	#1
Anthonydi Stock Join Date: Jun 2010 Location: Maryville,TN Posts: 11	Yeah the first thing I ever did to the car aftermarket was I installed an aem uego, as well as a bigger boost and water temp gauge. As far as the mileage goes it currently has 160xxx. I didnt put it on the list but before I up the hp at all I plan to replace all gaskets, seals, hoses, vacum lines, etc. Im not upping the hp at all till I know the engine can handle it I just didnt put it down cause I figured it was common sense lol. What I meant about the methanol injection kit is from my understanding isnt that bad for the internals. Like wont it burn them up or am I far off I dont know alot about methanol injection

01-26-2011, 09:52 PM	#3
Anthonydi Stock Join Date: Jun 2010 Location: Maryville,TN Posts: 11	Ok and after all that I should be pushing 400