Help after rebuild 7mgte

MJG · 11-02-2010, 03:15 AM

Having not experienced the results first hand, have you checked your crank is not 180 degrees out from your cams?
I would doubt the engine would start, however, if it did???

btwilson86 · 11-02-2010, 03:33 AM

Quote:

Originally Posted by MJG

Having not experienced the results first hand, have you checked your crank is not 180 degrees out from your cams?
I would doubt the engine would start, however, if it did???

It shouldn't, I've made that mistake before. Before anything, FIX YOUR AIR LEAK. Also, did you set your timing with the jumper wire in the diagnostic box? If you didn't, your timing will still not be properly set.

MJG · 11-02-2010, 03:51 AM

Thank you for the correction Mr. Wilson. good to note.

cfurlan · 11-02-2010, 07:57 AM

Yeah I did check the timing with the jumper and it was at 10. It doesn't matter where I turn the CPS it still rins rough. I'll fix the air leak later today after work. One more note, it runs the same as before when I overheated the engine if that helps. It ran great before overheating though. The cause of overheating was due to a worn hose that blew out. Thanks all

cfurlan · 11-02-2010, 09:18 PM

well it is now throwing code 52, knock sensor. I ensure that it was plugged in so I do not know why its going off unless its running so bad it thinks its a knock. I also tried pulling the plug wires while it was running. I pulled 1, 6, and 3 and there was no change in the engine performance. I didn't get to the other three yet.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
7mgte rebuild questions	bradenman1	MKIII Supra	0	05-27-2010 03:36 PM
7mgte performance motor rebuild	tommy951	Non-Generation Specific Questions	1	11-02-2008 01:58 AM
88 7mgte Rebuild	SocalSupra	Non-Generation Specific Questions	1	09-26-2008 06:57 PM
Should i REbuild 7mgte or just buy 1	WhiteTurboZ89	Show n Tell	2	02-07-2008 01:09 PM

11-02-2010, 03:15 AM	#1
MJG 3" Exhaust Join Date: Mar 2010 Location: Washington State Posts: 125	Having not experienced the results first hand, have you checked your crank is not 180 degrees out from your cams? I would doubt the engine would start, however, if it did???

11-02-2010, 03:51 AM	#3
MJG 3" Exhaust Join Date: Mar 2010 Location: Washington State Posts: 125	Thank you for the correction Mr. Wilson. good to note.

11-02-2010, 07:57 AM	#4
cfurlan Intake Join Date: Oct 2010 Location: Indiana Posts: 38	Yeah I did check the timing with the jumper and it was at 10. It doesn't matter where I turn the CPS it still rins rough. I'll fix the air leak later today after work. One more note, it runs the same as before when I overheated the engine if that helps. It ran great before overheating though. The cause of overheating was due to a worn hose that blew out. Thanks all

11-02-2010, 09:18 PM	#5
cfurlan Intake Join Date: Oct 2010 Location: Indiana Posts: 38	well it is now throwing code 52, knock sensor. I ensure that it was plugged in so I do not know why its going off unless its running so bad it thinks its a knock. I also tried pulling the plug wires while it was running. I pulled 1, 6, and 3 and there was no change in the engine performance. I didn't get to the other three yet.