07-16-2010, 01:26 PM
|
#1 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
 |
might be getting a mk3 again :)
HAHAHAHAHAHa
ok so there is an add up for a mk3 non turbo with 160'000k and a broken auto tranny, and i have a w58 from an 87 non turbo in my garage right now. gona get it cheap hopefully and have another mk3 and this is perfect because my mk2 isnt going to be on the road until next spring at the latest...
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
07-18-2010, 01:35 AM
|
#2 |
|
Supra Forum Moderator
Join Date: Nov 2009
Location: Green-Ohio
Posts: 1,297
|
see if you can talk him down to 600.. +)
__________________
 92 Ma71 7mGTE Auto. SafcII Supra FAQ Supra MKIII FAQ Classified Section guidelines : |
|
|
|
|
07-19-2010, 12:18 AM
|
#3 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
|
picking it up on friday for 500dollers
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
|
07-19-2010, 12:49 AM
|
#4 |
|
3" Exhaust
Join Date: Apr 2010
Location: Stoney Creek
Posts: 178
|
congratz nothing like a new car to start workin on =D
__________________
1987 N/A 7MGE manual transmission slight rod knock  never driven it yet... legally~
|
|
|
|
|
07-19-2010, 08:49 PM
|
#5 |
|
Supra Forum Moderator
Join Date: Nov 2009
Location: Green-Ohio
Posts: 1,297
|
500.. not bad!
__________________
92 Ma71 7mGTE Auto. SafcII Supra FAQ Supra MKIII FAQ Classified Section guidelines : |
|
|
|
|
07-21-2010, 12:28 AM
|
#6 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
|
im hardened in the arts of being a jew.
got all my mk3 parts out yesterday, still have a drivers seat, strut tower bar, mint center consol w/ cup holders from an 89, some spare signals and tail lights, and tomarow i might start putting a clutch together for ,my trans. also i need to change the fluid and throw out bearing and get it all ready to go in the car. also friday buying a clutch and brake pedal,w/ assembly plus i have all the boots and leather thingy to go with. ill get pics up asap when i get it home.
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
|
07-21-2010, 12:30 AM
|
#7 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
|
would a clutch from a 5m-ge hold a stock 7m-ge?? i dont have any mods planned until i buy a good clutch i just have an old 5m clutch lying around...
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
|
07-21-2010, 01:11 AM
|
#8 |
|
Super Moderator
Join Date: May 2007
Location: Billings, Montana
Posts: 1,034
|
Looks like the 2 clutches are the same part number, so I'd say you're good to go!
__________________
1989 7MGTE R154 Targa Top White Package w/Blue Interior Driftmotion 57trim CT26, Upgraded Intercooler, 2.25" Hard Pipes, 3" Turbo Back Exhaust with Test Pipe, HKS VPC w/GM 3 bar MAP sensor, APEXi S-AFC, Walbro 255lph fuel pump, ProSport EVO Series Boost / Fuel Pressure / AFR gauges, Lotek a Pillar Gauge Pod, HKS Type 0 Turbo Timer, Eibach Lowering Springs, Tokico Illumina II TEMS struts, custom powder coated Motegi Racing TrakLite wheels |
|
|
|
|
07-26-2010, 04:41 AM
|
#9 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
|
so i ordered valve cover and intake manifold gasket set, aswell as a throwout bearing. i ran out of light, but i got the valve covers done, and the intake manifold all off, and cleaned.
gona be some good before and after pics.
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
