might be getting a mk3 again :)

Green7mgte · 07-19-2010, 08:49 PM

500.. not bad!

CanadianBak'inSupra · 07-21-2010, 12:28 AM

im hardened in the arts of being a jew.
got all my mk3 parts out yesterday, still have a drivers seat, strut tower bar, mint center consol w/ cup holders from an 89, some spare signals and tail lights, and tomarow i might start putting a clutch together for ,my trans. also i need to change the fluid and throw out bearing and get it all ready to go in the car.
also friday buying a clutch and brake pedal,w/ assembly plus i have all the boots and leather thingy to go with.
ill get pics up asap when i get it home.

CanadianBak'inSupra · 07-21-2010, 12:30 AM

would a clutch from a 5m-ge hold a stock 7m-ge?? i dont have any mods planned until i buy a good clutch i just have an old 5m clutch lying around...

btwilson86 · 07-21-2010, 01:11 AM

Looks like the 2 clutches are the same part number, so I'd say you're good to go!

CanadianBak'inSupra · 07-26-2010, 04:41 AM

so i ordered valve cover and intake manifold gasket set, aswell as a throwout bearing. i ran out of light, but i got the valve covers done, and the intake manifold all off, and cleaned.
gona be some good before and after pics.

07-19-2010, 08:49 PM	#1
Green7mgte Supra Forum Moderator Join Date: Nov 2009 Location: Green-Ohio Posts: 1,297	500.. not bad! __________________ 92 Ma71 7mGTE Auto. SafcII Supra FAQ Supra MKIII FAQ Classified Section guidelines :

07-21-2010, 12:28 AM	#2
CanadianBak'inSupra Official hall monitor / search nazi - NO SOUP FOR YOU! Join Date: Oct 2009 Location: Canada, BC Posts: 837	im hardened in the arts of being a jew. got all my mk3 parts out yesterday, still have a drivers seat, strut tower bar, mint center consol w/ cup holders from an 89, some spare signals and tail lights, and tomarow i might start putting a clutch together for ,my trans. also i need to change the fluid and throw out bearing and get it all ready to go in the car. also friday buying a clutch and brake pedal,w/ assembly plus i have all the boots and leather thingy to go with. ill get pics up asap when i get it home. __________________ 1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft.

07-21-2010, 12:30 AM	#3
CanadianBak'inSupra Official hall monitor / search nazi - NO SOUP FOR YOU! Join Date: Oct 2009 Location: Canada, BC Posts: 837	would a clutch from a 5m-ge hold a stock 7m-ge?? i dont have any mods planned until i buy a good clutch i just have an old 5m clutch lying around... __________________ 1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft.

07-21-2010, 01:11 AM	#4
btwilson86 Super Moderator Join Date: May 2007 Location: Billings, Montana Posts: 1,034	Looks like the 2 clutches are the same part number, so I'd say you're good to go! __________________ 1989 7MGTE R154 Targa Top White Package w/Blue Interior Driftmotion 57trim CT26, Upgraded Intercooler, 2.25" Hard Pipes, 3" Turbo Back Exhaust with Test Pipe, HKS VPC w/GM 3 bar MAP sensor, APEXi S-AFC, Walbro 255lph fuel pump, ProSport EVO Series Boost / Fuel Pressure / AFR gauges, Lotek a Pillar Gauge Pod, HKS Type 0 Turbo Timer, Eibach Lowering Springs, Tokico Illumina II TEMS struts, custom powder coated Motegi Racing TrakLite wheels

07-26-2010, 04:41 AM	#5
CanadianBak'inSupra Official hall monitor / search nazi - NO SOUP FOR YOU! Join Date: Oct 2009 Location: Canada, BC Posts: 837	so i ordered valve cover and intake manifold gasket set, aswell as a throwout bearing. i ran out of light, but i got the valve covers done, and the intake manifold all off, and cleaned. gona be some good before and after pics. __________________ 1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft.