7mgte issues need help doing diag

touge_monster86 · 03-07-2010, 09:33 PM

no luck man nothing changed. its like the injectors are not working

cre · 03-07-2010, 09:51 PM

Well, if you're sure it's fuel get a gauge on the fuel rail and get an actual pressure reading. If pressure is good check on the grounds which bolt to the side of the intake plenum again; pull them and scrub them and the manifold where they mount with sandpaper or a wire brush.

Oh, sorry, when you asked which pins I thought you were asking about jumping the fuel pump... To check codes see here: http://www.cygnusx1.net/Supra/TechTi...ror_codes.aspx

Is the injector resistor pack on the driver's side wheel well plugged in? Test it for 12v+ at the black wire with the orange stripe with the ignition in the ON position.

MA70-3.0GT · 03-08-2010, 05:51 PM

Just a thought, with the FP bridge in place & ign. on can you hear the fuel pump running & the regulator on the fuel rail blowing off excess (hissing sound)?

If not then the pump or it's wiring are an issue. You said the pump relay gets really hot, I'm not sure how hot but if it's overheating then it could either be the pump drawing excess current or a dodgy relay, the results of the wire bridge would suggest which.

touge_monster86 · 03-08-2010, 10:27 PM

when i bridge the fp it still comes on and i do here the hissing sound. i made sure that the resister box is grounded to the chassis properly and checked to see if its plugged in. still same result . i also checked to see if the cold start injector " the one under the intake manifold i think that's the name for it not sure" had pressure and it dose . i checked the ground from the ecu to the manifold as well and it is clean and in a good spot. i do have one question i exstended it and had to solder to make the ecu grounds long that would not affect its abbility to creat a stable ground would it ?

i also tested the resistor's B wire with O stripe and i did not get 12v+ i got 11.09V+

whats that about?

03-07-2010, 09:33 PM	#1
touge_monster86 Stock Join Date: Mar 2010 Location: huntington beach Posts: 11	diag no luck man nothing changed. its like the injectors are not working

03-07-2010, 09:51 PM	#2
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Well, if you're sure it's fuel get a gauge on the fuel rail and get an actual pressure reading. If pressure is good check on the grounds which bolt to the side of the intake plenum again; pull them and scrub them and the manifold where they mount with sandpaper or a wire brush. Oh, sorry, when you asked which pins I thought you were asking about jumping the fuel pump... To check codes see here: http://www.cygnusx1.net/Supra/TechTi...ror_codes.aspx Is the injector resistor pack on the driver's side wheel well plugged in? Test it for 12v+ at the black wire with the orange stripe with the ignition in the ON position. __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

03-08-2010, 05:51 PM	#3
MA70-3.0GT 12psi boost Join Date: Oct 2009 Location: Crewe, England Posts: 356	Just a thought, with the FP bridge in place & ign. on can you hear the fuel pump running & the regulator on the fuel rail blowing off excess (hissing sound)? If not then the pump or it's wiring are an issue. You said the pump relay gets really hot, I'm not sure how hot but if it's overheating then it could either be the pump drawing excess current or a dodgy relay, the results of the wire bridge would suggest which. __________________ '89 MA70 Supra GT aero 3.0turbo JDM, Rebuilt motor, K&N intake, 3" stainless turbo-back. New turbo and braided line kit... '89 Honda NC27 400, NC23 cams, open pipe, PC36a shock & possibly Showa USD forks... '83 Yamaha 29R XJ750E-II, number 69 off the line, only runner in the country? Original except Koni shocks '95 Honda PC26 CB500R, Winter hack, hateful, trying to sell it I'm not paranoid, they really ARE after me!!!

03-08-2010, 10:27 PM	#4
touge_monster86 Stock Join Date: Mar 2010 Location: huntington beach Posts: 11	when i bridge the fp it still comes on and i do here the hissing sound. i made sure that the resister box is grounded to the chassis properly and checked to see if its plugged in. still same result . i also checked to see if the cold start injector " the one under the intake manifold i think that's the name for it not sure" had pressure and it dose . i checked the ground from the ecu to the manifold as well and it is clean and in a good spot. i do have one question i exstended it and had to solder to make the ecu grounds long that would not affect its abbility to creat a stable ground would it ? i also tested the resistor's B wire with O stripe and i did not get 12v+ i got 11.09V+ whats that about? Last edited by touge_monster86; 03-08-2010 at 11:26 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
7MGTE to 7MGE	karu	MKIII Supra	4	10-22-2010 07:22 AM
7MGTE Wiring Harness Issues	JMoses	MKIII Supra	12	06-03-2009 01:56 PM
JDM 7mgte help	98fxdwg	Non-Generation Specific Questions	0	10-30-2007 05:45 AM
7mgte and 7mge question	supraman121	MKIII Supra	2	01-12-2007 09:09 PM