Forum: MKII Supra
06-03-2011, 06:30 AM
|
|
Replies: 136
Views: 33,564
|
Forum: MKIII Supra
06-03-2011, 03:14 AM
|
|
Replies: 34
Views: 10,602
if u unclip anything on the harness u should...
if u unclip anything on the harness u should always tag both ends so you know where they went.
if they can only reach one injector (usually this is how the harnesses work on these motors, not...
|
Forum: MKIII Supra
06-03-2011, 01:50 AM
|
|
Replies: 8
Views: 11,433
|
Forum: MKIII Supra
06-03-2011, 01:26 AM
|
|
Replies: 34
Views: 10,602
|
Forum: MKIII Supra
06-03-2011, 01:14 AM
|
|
Replies: 8
Views: 11,433
as in a flutter sound like...? instead of a...
as in a flutter sound like...? instead of a constant pulse or pressure relief sound, it pulses up and down?
ive never heard of one being made to do that. that is the sign of an improperly...
|
Forum: MKIII Supra
06-03-2011, 12:52 AM
|
|
Replies: 34
Views: 10,602
sounds like the circuit opening relay for the...
sounds like the circuit opening relay for the fuel pump.
when you turn the key to the on position, the fuel pump runs for a few seconds to prime the lines and fuel rail, then stops. that supplies...
|
Forum: MKIII Supra
06-03-2011, 12:46 AM
|
|
Replies: 15
Views: 5,415
i think weve all gotten off subject here.
...
i think weve all gotten off subject here.
transmission problems are the issue here, not when/where/how to drift.
to me, it sounds like the main shaft bearings are going out in the tranny, or...
|
Forum: MKIII Supra
05-29-2011, 02:33 AM
|
|
Replies: 5
Views: 3,232
|
Forum: MKIII Supra
05-28-2011, 08:09 PM
|
|
Replies: 5
Views: 3,232
sounds like 5m vs 7m mounts. you should be able...
sounds like 5m vs 7m mounts. you should be able to take your old mounting brackets and put them on your new motor in the same place as your old one. all the holes on my block have all been tapped....
|
Forum: MKIII Supra
05-26-2011, 09:25 AM
|
|
Replies: 90
Views: 30,056
just go to a parts store and say you need the...
just go to a parts store and say you need the clutch lines. or take yours off and take them in, they can usually bend the hardlines and get you replacement soft lines when you take them the actual...
|
Forum: MKIII Supra
05-24-2011, 07:56 PM
|
|
Replies: 6
Views: 3,229
|
Forum: MKIII Supra
05-24-2011, 05:46 AM
|
|
Replies: 6
Views: 3,118
|
Forum: MKIII Supra
05-24-2011, 05:39 AM
|
|
Replies: 2
Views: 2,434
|
Forum: MKIII Supra
05-24-2011, 05:19 AM
|
|
Replies: 11
Views: 6,492
i would still get the alignment checked. most...
i would still get the alignment checked. most places will check for free and its worth while insurance.
make sure they show you a printout of all the measurements. if they dont offer this, go to...
|
Forum: MKIII Supra
05-23-2011, 08:50 AM
|
|
Replies: 6
Views: 3,118
basically a high performance daily driver. so...
basically a high performance daily driver. so yea, if you want to drop the dough on them, the cp pistons and eagle rods would be a good investment.
lighten up the rotating assembly and be a lil...
|
Forum: MKIII Supra
05-23-2011, 02:14 AM
|
|
Replies: 6
Views: 3,118
its been covered a bit. but anyway, as for 400...
its been covered a bit. but anyway, as for 400 hp, theres a few things we need to know.
is your car a turbo or N/A? if its turbo, simple upgrades can get you close. if its N/A, good luck with 400...
|
Forum: MKIII Supra
05-22-2011, 08:01 PM
|
|
Replies: 90
Views: 30,056
|
Forum: MKIII Supra
05-22-2011, 07:59 PM
|
|
Replies: 1
Views: 2,156
almost had this problem when replacing the auto...
almost had this problem when replacing the auto in my sisters 01 nissan xterra. had a lil more room than a 1/4 inch, about 3/4 prolly.
at first i was puzzled as to why the tranny wouldnt go on the...
|
Forum: MKIII Supra
05-22-2011, 07:54 PM
|
|
Replies: 6
Views: 3,229
|
Forum: MKIII Supra
05-18-2011, 08:28 AM
|
|
Replies: 6
Views: 3,109
|
Forum: MKIII Supra
05-18-2011, 08:24 AM
|
|
Replies: 10
Views: 5,121
|
Forum: MKII Supra
05-12-2011, 07:46 PM
|
|
Replies: 16
Views: 6,077
|
Forum: MKII Supra
05-12-2011, 02:50 AM
|
|
Replies: 16
Views: 6,077
damn hose....:squint:
haha, sounds like a...
damn hose....:squint:
haha, sounds like a plan, id "fluff" the head a bit, pretty easy to do with a dremel and a couple bits. picked up 20+ CFM on mine with a pretty basic port job, bout 12 hours...
|
Forum: MKIII Supra
05-12-2011, 02:42 AM
|
|
Replies: 6
Views: 2,757
apologies, i should have used the term...
apologies, i should have used the term hypereutectic. high silica (meant to be silicon) content was a bad choice of words. anyway, supra forums has an article concerning toyotas piston manufacturing...
|
Forum: MKIII Supra
05-10-2011, 05:25 AM
|
|
Replies: 2
Views: 2,195
|