Forum: MKIII Supra
04-22-2013, 02:55 AM
|
Replies: 3
Views: 2,104
cam position sensor internal seal
I have a 1987 supra with 44k miles. I replaced the oring at the gear. There is no evidence the internal seal is leaking but I wonder if I should replace it due to its age?
|
Forum: MKIII Supra
03-18-2013, 04:30 PM
|
Replies: 2
Views: 1,821
HKS turbo timer
I installed an HKS type 1 on my 1987 Supra but the rpm indication is reading zero. The pin its connected to at the ECM is black, I checked and there is no voltage. Should there be? Did the...
|
Forum: MKIII Supra
12-02-2011, 07:18 PM
|
Replies: 1
Views: 1,176
A/C clutch will not engage 4 several hours
I recently converted to R134a. I added the correct amount of oil( I think) and replaced the o-rings and dryer. When initially re-charging it the suction pressure got down to 5# and the clutch did not...
|
Forum: MKIII Supra
02-21-2011, 06:54 AM
|
Replies: 0
Views: 1,528
RT downpipe
I am looking at a downpipe for my 7mgte. The RT has most of the features Im looking for; stainless steel, non restricing flex section near the top and good fit. But if possible I'd like to find one...
|
Forum: MKIII Supra
02-21-2011, 06:47 AM
|
Replies: 5
Views: 2,159
Rad
I just installed a Fluidyne and love it!
|
Forum: MKIII Supra
02-05-2011, 06:40 PM
|
Replies: 2
Views: 2,063
timingbelt wobble
I started my engine (7mgte) after the timing belt install without the top cover on just to make sure everything is ok. It has a slight "wobble" front to back in what seems to be one spot on the belt...
|
Forum: MKIII Supra
02-02-2011, 07:09 AM
|
Replies: 4
Views: 2,239
|
Forum: MKIII Supra
02-01-2011, 01:43 AM
|
Replies: 4
Views: 2,239
Timing belt install
I installed a new timing belt and need a little help. I installed it on the crank pully then the oil pump, intake then exhaust pulley and then the tensioner. I then loosened the tensioner bolt and...
|
Forum: MKIII Supra
12-28-2010, 11:51 PM
|
Replies: 2
Views: 1,650
Radiator
I need to replace my radiator in my '87 Turbo. I would like something that bolts right in with NO mods yet is more efficient than stock and is of top quality. I would appreciate you input!
|
Forum: MKIII Supra
12-11-2010, 10:16 AM
|
Replies: 9
Views: 6,484
clips
Try www.northlandfasteners.com/MouldingClips
|
Forum: MKIII Supra
12-06-2010, 08:34 PM
|
Replies: 1
Views: 1,430
Toyota or Felpro
Is there any difference in quality between a Toyota head gasket set and Felpro?
|
Forum: MKIII Supra
12-02-2010, 04:21 PM
|
Replies: 14
Views: 3,123
head bolt idea
I dont have a blown head gasket but i was thinking of either replacing the head bolts one at a time or simply re-torquing the factory ones to a higher spec. Can this be done and if so what bolt order...
|