Now you need to take a good look at the wiring diagram for you car. And swap the pins from the USDM connector to the new one that came with the folding mirror switch.

You need a pick to release the lock on the JDM connector. When I compared the USDM I found the US pins don't use the lock like the JDM pins do, I didn't find that to be a problem they fit in fine. But when you put the connector into the switch after you swapped the pin you just need to make sure you push the pins in from the back side to make sure they are seated.

http://sphotos.ak.fbcdn.net/hphotos-..._1391694_n.jpg
The Orange wire was the only one you need to reuse from the JDM connector. It is the signal wire the the module to fold the mirrors.
http://sphotos.ak.fbcdn.net/hphotos-..._3196385_n.jpg

After I swapped all the pins I plugged in the new mirror switch to make sure the mirrors still operate correctly - Up Down Side To Side. The mirroes should work normally, if not recheck your wiring.

I worked on the passenger door next. The folding mirror control module hides in the passengers door.

http://sphotos.ak.fbcdn.net/hphotos-..._1753970_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-...5_985913_n.jpg

The module sits in the hole in the front of the door, like the door control module on the drivers side. But you are missing the yellow grommets on the passengers side.

http://hphotos-snc3.fbcdn.net/hs310...._8066963_n.jpghttp://hphotos-snc3.fbcdn.net/hs330...._8021170_n.jpg

If you have some spares pop them in, I had a few laying around. But if you don't taking 2 from the speaker shouldn't be a problem.

Next is running wiring out of passenger door. You have to add 7 new wires. 4 for the extra 4 wires on you need for the drivers side folding mirror. 1 for the signal from the switch. And a 20amp power and a ground. I made it easy on myself and pulled the harness out, rather then messing around.

http://sphotos.ak.fbcdn.net/hphotos-...6_870850_n.jpghttp://sphotos.ak.fbcdn.net/hphotos-..._1777793_n.jpg

Next I swapped the wiring at the passenger mirror

http://sphotos.ak.fbcdn.net/hphotos-..._8149005_n.jpghttp://hphotos-snc3.fbcdn.net/hs310...._3444239_n.jpg

On my car I ended up with 2 extra wires from the USDM, for heated outside mirrors I believe. I taped them up and pulled them back into the sleeve to get them out of the way.

http://hphotos-snc3.fbcdn.net/hs310...._2784369_n.jpg

After that I ran 4 new wires through the sleeve and wired them into the JDM harness to the folding mirror control module. And tied in the wiring I ran through the door harness.

http://sphotos.ak.fbcdn.net/hphotos-..._4838387_n.jpg

Then I installed the module.

http://sphotos.ak.fbcdn.net/hphotos-...2_403978_n.jpghttp://sphotos.ak.fbcdn.net/hphotos-..._5660301_n.jpg

After that I took the drivers door apart and did almost the same wiring as the passengers side, expect you only need to run 4 wires out of the drivers door. Connect all the wiring from the drivers door to the wiring that was run out of the passenger. Give it a ground. and find a good power source. I haven't decided yet were to get my power from. The JDM wiring diagram say you should use a 20amp fuse, but I jumped it to the cigarette lighter and worked fine so got to do some more work and get it off the cig lighter.


http://sphotos.ak.fbcdn.net/hphotos-...4_551224_n.jpg


Have fun be careful and enjoy

Originally Posted by TSupraT (Post 83464) Awesome work! It would be cool to see them auto-fold in when you shut the car off! Maybe a new project for ya?