Timing question.

cre · 04-25-2008, 12:20 AM

RTFM = Read The F@#$ing Manual

supramacist · 04-25-2008, 12:30 AM

Hey man..., when I'm actually working. I figure it out faster than I can normally find it in the manual. I have been in that biotch today.

But I'm stupid like this. I may not know the names of everything. But once I get done fixing them I won't forget anytime soon.

I think I'm going to woman up and just get a new dashpot on order.

Hello. Here's the kicker a few days back I notice a couple of bee's in the garage no biggie shut em out, they leave. Right now as I type a hive is eating its way out of an empty box for my air compressor. I have the stereo on and I can still hear them hum. I think I may need a priest.

So anyway. I came back up hoping someone could just affirmate my direction and kill a few minutes since I didn't un hook the battery. And I have. Thank You.

I'm gone.

supramacist · 04-25-2008, 01:12 AM

OK.

It's showing no codes. I tested the dashpot as cre said. It acted just as it should have.

It seems that the dashpot doesn't want to decompress fully which in turn is slowly bumping the idle up. Till it just jumps open to 2000 rpm'ish then it sticks.

The idle is steady on the 10 mark. I don't go much for that advanced timing schmaz..., but to each there own.

Even when reving by hand or in the car the dashpot just seems hesitant to let the hammer drop fully.

I think we have Found my problem.

On a lighter note the AFM and the cheapo 10$ filter have worked well.
I did as you fellers told me and haven't had an issue with the coolant light at all today. Idling or driving

cre · 04-25-2008, 01:55 AM

Try clamping the dashpot's actuator down with a zip tie, then go for a drive. The only thing that'll happen with the dashpot's plunger rendered inactive is that the engine with spike rich when you dump the throttle... the car may jerk a little (try to slow harder than usual) at that point.

If the idle returns to normal and the TPS is properly set, and the code 51 is gone, THEN you may proceed with setting the timing.

supramacist · 04-25-2008, 02:09 AM

When applying pressure to the dashpot it seems like it's going to kill the engine.

cre · 04-25-2008, 03:39 AM

Quote:

Originally Posted by supramacist

When applying pressure to the dashpot it seems like it's going to kill the engine.

Really? Were you or were you not doing something to manually adjust the idle? If so, then I'd start with trying to undo it.

supramacist · 04-25-2008, 04:50 AM

Well it never killed it but it wanted too it seemed.

I think I undid everything this last time around. Battery disconnect.
Hooked it back up. I was still throwing 51.

Went out and adjusted the dizzy, locked it in on 10. I set the idle screw back to where it was in the 1st place before doing so.

I"m still missing something and now I'm just too tired to keep thinking about it. Even though I want to. As it sits right now. It's in time and has no codes.

I'm about to have my last smoke of the day and call it quits till tomorrow.

I have just the zip tie for your project and I'll play around with it all day again, I'm sure sinse it's not done yet.

Why can't my dashpot just need to be replaced?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1991 n/a timing problems	jerrods91supra	Non-Generation Specific Questions	0	07-06-2008 09:44 PM
advanced timing?	sd88supra	MKIII Supra	7	04-27-2008 03:44 PM
Can't adjust timing...	Lunch2000	MKIII Supra	7	11-26-2006 04:09 AM
timing question (weed todd did)	joel w	MKIII Supra	6	09-26-2005 03:32 PM
Timing question	DeDom18	MKIII Supra	1	08-17-2005 07:50 AM

04-25-2008, 12:20 AM	#1
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	RTFM = Read The F@#$ing Manual

04-25-2008, 12:30 AM	#2
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	Hey man..., when I'm actually working. I figure it out faster than I can normally find it in the manual. I have been in that biotch today. But I'm stupid like this. I may not know the names of everything. But once I get done fixing them I won't forget anytime soon. I think I'm going to woman up and just get a new dashpot on order. Hello. Here's the kicker a few days back I notice a couple of bee's in the garage no biggie shut em out, they leave. Right now as I type a hive is eating its way out of an empty box for my air compressor. I have the stereo on and I can still hear them hum. I think I may need a priest. So anyway. I came back up hoping someone could just affirmate my direction and kill a few minutes since I didn't un hook the battery. And I have. Thank You. I'm gone.

04-25-2008, 01:12 AM	#3
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	OK. It's showing no codes. I tested the dashpot as cre said. It acted just as it should have. It seems that the dashpot doesn't want to decompress fully which in turn is slowly bumping the idle up. Till it just jumps open to 2000 rpm'ish then it sticks. The idle is steady on the 10 mark. I don't go much for that advanced timing schmaz..., but to each there own. Even when reving by hand or in the car the dashpot just seems hesitant to let the hammer drop fully. I think we have Found my problem. On a lighter note the AFM and the cheapo 10$ filter have worked well. I did as you fellers told me and haven't had an issue with the coolant light at all today. Idling or driving

04-25-2008, 01:55 AM	#4
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Try clamping the dashpot's actuator down with a zip tie, then go for a drive. The only thing that'll happen with the dashpot's plunger rendered inactive is that the engine with spike rich when you dump the throttle... the car may jerk a little (try to slow harder than usual) at that point. If the idle returns to normal and the TPS is properly set, and the code 51 is gone, THEN you may proceed with setting the timing.

04-25-2008, 02:09 AM	#5
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	When applying pressure to the dashpot it seems like it's going to kill the engine.

04-25-2008, 04:50 AM	#7
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	Well it never killed it but it wanted too it seemed. I think I undid everything this last time around. Battery disconnect. Hooked it back up. I was still throwing 51. Went out and adjusted the dizzy, locked it in on 10. I set the idle screw back to where it was in the 1st place before doing so. I"m still missing something and now I'm just too tired to keep thinking about it. Even though I want to. As it sits right now. It's in time and has no codes. I'm about to have my last smoke of the day and call it quits till tomorrow. I have just the zip tie for your project and I'll play around with it all day again, I'm sure sinse it's not done yet. Why can't my dashpot just need to be replaced?