replaced BHG and still milky oil

SilenceboneSupra · 01-14-2008, 07:55 PM

hi, i noticed that the engine had milky oil so we dissambled the engine and found the BHG, the engineblock looked allright no cracks at all! we cleaned the engine inside and out completely and retorqued the engine

.....
after done with the engine after a few days again it had milky oil

.......
anyone have any idea why i still get milky oil in the engine
we are sure there is no cracks on the block and i dont think the new HG could of let go in just a few days ....
any tips would help(i think)

mkiiisupra · 01-14-2008, 08:19 PM

If your head wasnt resurfaced i could still be leaking

supramacist · 01-15-2008, 01:04 AM

My thoughts also.

You never mentioned the head.
You have to have it machined because the alluminum
expands, contracts and warps.

This would be my gues as to why you still have a bhg.

SilenceboneSupra · 01-15-2008, 01:57 AM

well thanks for that il let a mechanic do that for me.....

supramacist · 01-15-2008, 02:16 AM

See the block is cast iron and the head is alluminum.
They both have different stress levels.
The cast iron will never warp enough for your eyes to see.
THe alluminum will but you'll have no way of knowing how much till its machined.

I would also incorporate ARP hardware and HKS mhg.
Probably a stopper. But none of that matters if you don't have atleast the head machined.

01-14-2008, 07:55 PM	#1
SilenceboneSupra 3" Exhaust Join Date: Oct 2007 Location: Aruba Posts: 113	replaced BHG and still milky oil hi, i noticed that the engine had milky oil so we dissambled the engine and found the BHG, the engineblock looked allright no cracks at all! we cleaned the engine inside and out completely and retorqued the engine..... after done with the engine after a few days again it had milky oil ....... anyone have any idea why i still get milky oil in the engine we are sure there is no cracks on the block and i dont think the new HG could of let go in just a few days .... any tips would help(i think)

01-14-2008, 08:19 PM	#2
mkiiisupra Lexus & 550's Join Date: Sep 2007 Location: Las Vegas, NV Posts: 570 Blog Entries: 1	If your head wasnt resurfaced i could still be leaking __________________ 1990 Toyota Supra Turbo A/T ------------------------------------------------ Questions about oil? take a look http://www.supramania.com/aehaas/

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-15-2008, 01:04 AM	#3
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	My thoughts also. You never mentioned the head. You have to have it machined because the alluminum expands, contracts and warps. This would be my gues as to why you still have a bhg.

01-15-2008, 01:57 AM	#4
SilenceboneSupra 3" Exhaust Join Date: Oct 2007 Location: Aruba Posts: 113	well thanks for that il let a mechanic do that for me.....

01-15-2008, 02:16 AM	#5
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	See the block is cast iron and the head is alluminum. They both have different stress levels. The cast iron will never warp enough for your eyes to see. THe alluminum will but you'll have no way of knowing how much till its machined. I would also incorporate ARP hardware and HKS mhg. Probably a stopper. But none of that matters if you don't have atleast the head machined.